Home / Articles / Three-wire thread measurement: best wire size and M
Draw + calculate · Production

Three-wire thread measurement: best wire size and M

7 min read · updated 19 Nov 2026

The most accurate way to check a thread is to measure its pitch diameter (E), not the major or minor diameter. The standard shop method is the three-wire method: three equal wires are laid in the thread grooves (two on one side, one on the other) and a micrometer measures over them to give a reading M, which converts back to pitch diameter. This guide gives the best wire-size formula, the over-wires formula for 60° threads, a wire table, a worked M10×1.5 example, and how to lay the geometry out in DXCAD2D.

Why measure at the pitch diameter

The pitch diameter is the imaginary diameter where the thread tooth and groove are equal in width. It is what decides whether two threads fit. Three wires let you reach it without touching the crest or root, which are less well defined. The wires rest on the flanks of the thread, which relate directly to the pitch diameter.

60° dw pitch line E crest pitch P
A round wire dw rests in a 60° groove and touches both flanks at points on the pitch line E · P is the pitch (crest to crest).

Formula 1 — best wire size

The wire should be the size that touches the flanks right at the pitch line — not sinking to the root nor riding on the crest. For a 60° included-angle thread (metric and Unified) the best wire size is

Best wire size: dw = P ÷ (2 × cos 30°) = 0.57735 × P
where P is the pitch in mm · cos 30° = 0.86603
Pitch P (mm)Best wire (mm)Pitch P (mm)Best wire (mm)
0.500.2891.500.866
0.700.4041.751.010
0.800.4622.001.155
1.000.5772.501.443
1.250.7223.001.732

In practice use the nearest wire from a standard set (e.g. 0.866 for P 1.5). All three wires must be the same size and hardened.

Formula 2 — over-wires reading M (60° threads)

With three wires in place and a micrometer reading M over them, the formula linking M to the pitch diameter E for a 60° included-angle thread is

Over-wires reading: M = E + 3·dw − 0.86603·P
Solve back for pitch diameter: E = M − 3·dw + 0.86603·P

The 3 comes from (1 + 1/sin 30°) = 1 + 2 and 0.86603 comes from the cotangent of the half-angle — both fall straight out of the 60° groove geometry. The same constants apply to metric and UN threads with a 60° included angle.

Worked example — an M10×1.5 screw

Coarse M10 has pitch P = 1.5 mm. Its basic pitch diameter is E = d − 0.64952·P.

  1. Pitch diameter E = 10 − 0.64952 × 1.5 = 10 − 0.974 = 9.026 mm
  2. Best wire dw = 0.57735 × 1.5 = 0.866 mm
  3. Reading M = E + 3·dw − 0.86603·P
    = 9.026 + 3 × 0.866 − 0.86603 × 1.5
    = 9.026 + 2.598 − 1.299 = 10.325 mm
How to read it: if the real over-wires measurement is 10.325 mm the pitch diameter is on size. If it reads 10.30 mm the pitch diameter is 0.025 mm small (the thread is loose) — a change of one unit in M equals exactly one unit in E, because the coefficient of E is 1.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Lay the geometry out in the program to check

The real measurement uses a micrometer and wires, but drawing an enlarged section in DXCAD2D shows where the wire sits and confirms the numbers (set units to millimetres and draw at a large scale so it is easy to see).

  1. Draw the wire at full size: press C, click the centre, then type radius 0.433 (half of the 0.866 mm wire).
  2. Draw the 60° flanks: press L and draw two lines 30° either side of vertical so they touch the circle (turn on snapping to catch the edge).
  3. Repeat the groove one pitch away: press CO (copy) a distance of 1.5 along the axis, or use AR to array a row.
  4. Press D and dimension from the top of the top wire to the bottom of the bottom wire to compare with the calculated M.
  5. Press ME and measure crest to crest to confirm it equals the pitch P.

Frequently asked questions

What does the three-wire method measure

The thread's pitch diameter — the value that decides whether threads fit. It is more accurate than measuring the major or minor diameter because the wires touch the flanks right on the pitch line.

How do I pick the wire size for measuring a thread

Use the best wire size dw = 0.57735 × P. For a 1.5 mm pitch use a 0.866 mm wire; for a 1.0 mm pitch use 0.577 mm. All three wires must be equal in size and hardened.

What should an M10 coarse thread read over the wires

At the basic pitch diameter of 9.026 mm with 0.866 mm wires, M10×1.5 reads M = 10.325 mm over the wires. A smaller reading means the thread is undersize (loose); a larger reading means oversize (tight).

How do I get pitch diameter from the M reading

Use E = M − 3·dw + 0.86603·P for any 60° included-angle thread (metric and UN). Put in the measured M, the wire dw and the pitch P.

Does the three-wire method work on Acme threads

Yes, but with a different formula, because Acme/Tr threads have a 29°/30° included angle, not 60°. The constants 3 and 0.866 in this article apply only to 60° threads.

Summary

Three wires give the most accurate pitch-diameter reading on a thread. Remember two formulas: the best wire size dw = 0.57735 × P, and the over-wires reading for 60° threads M = E + 3·dw − 0.86603·P. For M10×1.5 that gives a 0.866 mm wire and M = 10.325 mm when the pitch diameter is on size. Drawing an enlarged section in DXCAD2D confirms the geometry before you measure the real part with a micrometer.