Draw and calculate Acme / Tr trapezoidal power-screw threads
Trapezoidal threads drive power screws — jacks, vice spindles, lathe lead screws — because the trapezoidal tooth carries axial load well and is easier to cut than a square thread. The metric system calls it Tr, with a 30° included thread angle; the inch system calls it Acme, with a 29° angle. This guide gives the formulas for every dimension, a worked Tr 30×6 example, and the steps to draw the tooth profile in DXCAD2D Online.
Key dimensions of a metric trapezoidal (Tr) thread
A Tr d×P thread is written with d = major (outside) diameter and P = pitch (crest-to-crest). The values you need are:
| Dimension | Formula (ISO 2901 / DIN 103) |
|---|---|
| Clearance ac | 0.25 (P 1.5–5) · 0.5 (P 6–12) · 1 (P ≥ 14) |
| Screw thread depth h₃ | 0.5P + ac |
| Screw minor dia d₃ | d − 2h₃ |
| Pitch dia d₂ | d − 0.5P |
| Nut minor dia D₁ | d − P |
| Nut major dia D₄ | d + 2ac |
| Lead (single start) | P (multi-start = n × P) |
Worked example: Tr 30 × 6, single start
Trapezoidal screw, major d = 30 mm, pitch P = 6 mm. A pitch of 6 falls in the 6–12 band, so ac = 0.5.
| Dimension | Substitute | Result |
|---|---|---|
| Thread depth h₃ | 0.5×6 + 0.5 | 3.5 mm |
| Screw minor dia d₃ | 30 − 2×3.5 | 23.0 mm |
| Pitch dia d₂ | 30 − 0.5×6 | 27.0 mm |
| Nut minor dia D₁ | 30 − 6 | 24.0 mm |
| Nut major dia D₄ | 30 + 2×0.5 | 31.0 mm |
| Tooth thickness at pitch line | P ÷ 2 | 3.0 mm |
| Crest flat width (approx) | 0.366 × P | 2.20 mm |
Lead angle (to check power transmission) λ = arctan( lead ÷ (π × d₂) ) = arctan( 6 ÷ (π × 27) ) = arctan(0.0707) = 4.05°. A lead angle this low tends to be self-locking (the screw does not back-drive when released), which suits a jack.
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineDrawing the tooth profile in DXCAD2D
Draw one tooth in axial section, then repeat it along the pitch. Using the Tr 30×6 numbers, put the minor-diameter line (d₃/2 = 11.5) at y = 0.
- Draw the minor-diameter line with L (line), horizontal at y = 0, as the tooth base.
- Build one tooth with PL (polyline), typing relative coordinates up the 15° flanks: thread depth h₃ = 3.5, so each flank runs 3.5×tan15° = 0.94 mm along the axis and the crest flat is 2.20 wide →
@0.94,3.5(up the left flank)@2.20,0(crest)@0.94,-3.5(down the right flank). - Check the angle with ME (measure), or confirm the flank is 15° from vertical (75° from horizontal).
- Repeat the tooth along the axis with AR (array), pitch spacing = 6 mm, count to suit the thread length.
- Draw the major-diameter line (major 30 → radius 15 from the axis) and pitch line (d₂ = 27 → 13.5) with O (offset) from the axis to control depth.
- Dimension the pitch, depth and minor diameter with DLI (dimension linear).
To draw the nut, flip the profile (the nut groove receives the screw tooth) using nut major D₄ = 31 and nut minor D₁ = 24 as limits, then MI (mirror) the profile to the other side of the axis.
Frequently asked questions
what is the minor diameter of a tr 30x6 thread
Screw minor diameter d₃ = 30 − 2×(0.5×6 + 0.5) = 23.0 mm. The pitch diameter d₂ = 27.0 mm and the nut minor diameter D₁ = 24.0 mm.
what is the acme thread angle
Metric Tr threads have a 30° included angle (15° per flank); inch Acme threads have a 29° included angle (14.5° per flank).
how to calculate trapezoidal thread depth
Screw thread depth h₃ = 0.5×pitch + clearance. The clearance is 0.25 (pitch 1.5–5), 0.5 (pitch 6–12) or 1 (pitch ≥ 14). For Tr 30×6 that gives h₃ = 3.5 mm.
what is the difference between acme and tr threads
The sections look alike but the angle differs: Tr is metric at 30°, Acme is inch at 29°. The main formulas are the same — you just change the flank angle and work in inches/TPI for Acme.
Summary
A trapezoidal power-screw thread comes from the pitch P and clearance ac: thread depth h₃ = 0.5P + ac, screw minor = d − 2h₃, pitch dia = d − 0.5P. For Tr 30×6 that gives d₃ = 23, d₂ = 27, D₁ = 24 and a 4.05° lead angle. Draw one tooth with PL along 15° flanks, array it at the 6 mm pitch, and verify every value with ME before cutting.