Tap drill size chart for M3–M20 metric threads
Before you tap a thread you must drill a pilot hole with a bit that is slightly smaller than the thread size. Too big and the thread is shallow and loose; too small and the tap binds and snaps. The shortcut machinists use everywhere is tap drill = thread size − pitch. This guide gives a tap drill chart for M3–M20 in both coarse and fine pitch, shows how it differs from a clearance hole, and explains how to draw the hole in DXCAD2D Online.
The shortcut: tap drill = thread size − pitch
Every metric thread has two values: the nominal size D (M8 = 8 mm) and the pitch P (the distance the thread advances per turn, in mm). The tap drill diameter comes straight from them.
Example: M8 coarse, P = 1.25 → tap drill = 8 − 1.25 = 6.75 ≈ 6.8 mm
This gives roughly 77% thread depth, which is strong enough yet easy to tap without snapping the tool. It suits almost any material, so it matches the standard tap drill sizes in the chart below for nearly every size.
Coarse-thread tap drill chart (most common)
| Thread | Pitch P (mm) | Tap drill (mm) |
|---|---|---|
| M3 | 0.5 | 2.5 |
| M4 | 0.7 | 3.3 |
| M5 | 0.8 | 4.2 |
| M6 | 1.0 | 5.0 |
| M8 | 1.25 | 6.8 |
| M10 | 1.5 | 8.5 |
| M12 | 1.75 | 10.2 |
| M14 | 2.0 | 12.0 |
| M16 | 2.0 | 14.0 |
| M20 | 2.5 | 17.5 |
Every value comes from D − P rounded to the nearest drill you can buy: M12 computes to 10.25, so you use a standard 10.2 mm bit.
Fine threads have a different pitch
The same nominal size can come in several pitches. A fine thread has a smaller pitch, so its tap drill is larger than the coarse one. Use D − P as before, just with that thread's pitch.
| Thread × pitch | Tap drill (mm) |
|---|---|
| M8 × 1.0 | 7.0 |
| M10 × 1.25 | 8.8 |
| M12 × 1.25 | 10.8 |
| M12 × 1.5 | 10.5 |
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineTap hole vs clearance hole
Do not confuse the two. A tap hole is for cutting a thread into the part, so it is smaller than the thread size (= D − P). A clearance hole lets a bolt pass through freely, so it is slightly larger than the thread size.
| Thread | Tap hole (mm) | Clearance, medium (mm) |
|---|---|---|
| M6 | 5.0 | 6.6 |
| M8 | 6.8 | 9.0 |
| M10 | 8.5 | 11.0 |
| M12 | 10.2 | 13.5 |
The clearance values follow the ISO medium fit. Use a smaller hole for a tight fit, a larger one to allow for misalignment.
Draw the hole in DXCAD2D
- Press C and draw a circle at the hole centre with radius equal to half the tap drill — a 6.8 mm drill means radius
3.4. - To show both the tap hole and the thread line, draw a second circle at radius D/2 (M8 → radius
4), drawn thin or as a 3/4 open circle by convention. - Press D to add the hole callout, e.g.
M8with the thread depth. - Press M to measure hole-to-hole spacing and check the coordinates before you issue the drawing.
Frequently asked questions
What drill size for M8 tap
M8 coarse (pitch 1.25) uses a 6.8 mm drill, from 8 − 1.25 = 6.75 rounded to 6.8. M8 fine (pitch 1.0) uses a 7.0 mm drill.
What is the tap drill for M10
M10 coarse (pitch 1.5) uses an 8.5 mm drill (10 − 1.5 = 8.5). For M10 × 1.25 use 8.8 mm.
What drill for M6 tap
M6 coarse (pitch 1.0) uses a 5.0 mm drill exactly (6 − 1 = 5).
How do you calculate tap drill size
Subtract the pitch from the thread size: tap drill = D − P. This gives about 77% thread depth, strong enough and easy to tap.
What is the difference between a tap hole and a clearance hole
A tap hole is smaller than the thread size so a thread can be cut into it; a clearance hole is larger so a bolt passes through. For M8 the tap hole is 6.8 mm but the clearance hole is about 9.0 mm.
Summary
One formula does it: tap drill = thread size − pitch, giving about 77% thread, which is both strong and easy to tap. So M8 takes a 6.8 mm drill, M10 takes 8.5, and M12 takes 10.2 — and do not confuse these with clearance holes, which must be larger than the thread size. When drawing in DXCAD2D, draw a circle with radius half the tap drill and add a thread callout.