Draw and calculate a square thread (power screw)
A square thread is a power-transmission thread whose flanks stand square to the axis, so friction is low and axial load transfers efficiently. You find it in jacks, vices and lead screws. Its formulas are simpler than a metric thread because the depth is just half the pitch and the land and groove are equal in width. This guide gives the full set of formulas, a worked Ø30 pitch-6 example, the lead angle, and the steps to draw the profile in DXCAD2D.
Square-thread formulas
A standard single-start square thread is defined by the pitch P alone. The tooth depth is half the pitch, which makes the land (crest) and the groove equal in width, each P/2.
Tooth depth h = P / 2
Land width = groove width = P / 2
Core (minor) dia d_c = d − 2·(P/2) = d − P
Mean dia d_m = d − P/2
Lead L = n·P (n = number of starts) · Lead angle: tan λ = L / (π·d_m)
Worked example: Ø30, pitch 6 mm
A square-thread power screw, major dia d = 30 mm, pitch P = 6 mm, single start.
1) Tooth depth: h = P/2 = 6/2 = 3.0 mm
2) Core diameter: d_c = d − P = 30 − 6 = 24 mm (3 mm deep on each side, 6 mm in total)
3) Mean diameter: d_m = d − P/2 = 30 − 3 = 27 mm
4) Land and groove: each P/2 = 3 mm wide
5) Lead and lead angle: lead L = P = 6 mm (single start) · tan λ = L/(π·d_m) = 6/(π × 27) = 6/84.82 = 0.07074 → λ = 4.05°
Square thread vs. ACME thread
| Feature | Square | ACME (29°) |
|---|---|---|
| Flank angle | 0° (square to axis) | 29° (tapered) |
| Depth | P/2 | 0.5P + 0.25 mm |
| Friction | Lowest | Slightly higher |
| Manufacture | Hard (needs a form tool) | Easier; taps/dies sold |
| Side load | Poor | Better (tapered flanks locate) |
The square thread gives the highest transmission efficiency, but it is hard to make and its backlash cannot be adjusted, so many real designs use ACME instead.
Draw the square-thread profile in DXCAD2D
Draw the axial section. Using d = 30, P = 6 (upper half of the axis: major line at y = 15, core line at y = 12):
- Press L and draw the axis at y = 0 as a reference line.
- Press P and draw one pitch of the profile by coordinates (start at the crest, outer edge):
0,15→#3,15(3 mm land) →#3,12(3 mm deep) →#6,12(3 mm groove) →#6,15(back up). - Press array and repeat the profile along the axis at a 6 mm pitch for as many threads as you need.
- Press mirror across the axis if you want the full section on both sides.
- Press D and dimension: pitch 6, depth 3, major 30, core 24 · use M to re-check the land and groove.
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineFrequently asked questions
How deep is a square thread
The tooth depth equals the pitch divided by two, e.g. a 6 mm pitch is 3 mm deep, and the land and groove are equal in width at P/2 each.
How do I calculate the core diameter of a square thread
Core diameter = major diameter − pitch (d − P), because the P/2 depth is cut on both sides, adding up to P. A Ø30 screw with pitch 6 has a 24 mm core.
What is the difference between a square thread and an ACME thread
A square thread has flanks square to the axis — lowest friction, but hard to cut and with no backlash adjustment. ACME has 29° flanks: easier to cut, taps and dies are available, and it takes side load better.
How do I find the lead angle of a square thread
tan λ = lead ÷ (π × mean diameter). For a single-start Ø30, pitch-6 screw, tan λ = 6/(π×27), giving λ ≈ 4.05°.
Summary
Square threads are easy to size: depth = P/2, land and groove each P/2, core dia = d − P, and mean dia = d − P/2. Find the lead angle from tan λ = L/(π·d_m). Draw the section as a one-pitch polyline and array it along the axis. If the design needs adjustable backlash or easy manufacture, consider an ACME thread instead.