Draw and calculate a worm gear: ratio, lead angle, centre distance
A worm gear (worm and worm wheel) gives a very high reduction in little space, and many pairs are also self-locking, so they suit hoists, roller-shutter drives and dividing heads. The calculation hinges on the module together with the number of worm starts and the wheel tooth count. This guide gives the formulas for ratio, lead angle, diameters and centre distance, with a worked 40:1 example and the steps to draw the pair in DXCAD2D Online.
Key dimensions of a worm gear
Let z₁ = number of worm starts, z₂ = number of wheel teeth, m = axial module (the worm's axial module equals the wheel's module), and q = the worm diameter factor.
| Dimension | Formula |
|---|---|
| Gear ratio i | z₂ ÷ z₁ |
| Axial pitch px | π × m |
| Worm lead pz | z₁ × π × m |
| Worm pitch dia d₁ | q × m |
| Lead angle γ | arctan( z₁ ÷ q ) |
| Wheel pitch dia d₂ | z₂ × m |
| Centre distance a | (d₁ + d₂) ÷ 2 |
| Worm outside dia da1 | d₁ + 2m |
| Wheel throat dia da2 | d₂ + 2m |
| Root dia df | d − 2.4m (worm and wheel) |
Worked example: a 40:1 ratio
Single-start worm z₁ = 1, wheel z₂ = 40 teeth, module m = 2 mm, diameter factor q = 10.
| Dimension | Substitute | Result |
|---|---|---|
| Gear ratio i | 40 ÷ 1 | 40 : 1 |
| Axial pitch px | π × 2 | 6.283 mm |
| Lead pz | 1 × π × 2 | 6.283 mm |
| Worm pitch dia d₁ | 10 × 2 | 20.0 mm |
| Lead angle γ | arctan(1 ÷ 10) | 5.71° |
| Wheel pitch dia d₂ | 40 × 2 | 80.0 mm |
| Centre distance a | (20 + 80) ÷ 2 | 50.0 mm |
| Worm outside dia da1 | 20 + 2×2 | 24.0 mm |
| Wheel throat dia da2 | 80 + 2×2 | 84.0 mm |
A 5.71° lead angle is low. Worm gears with a low lead angle (roughly < 5–6°) tend to be self-locking — the wheel cannot back-drive the worm — which suits hoists that must hold a load, at the cost of lower transmission efficiency than a spur gear.
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineDrawing the pair in DXCAD2D
Draw it as a 2D meshing view: the wheel as a circle, the worm as a side-view thread, to the 40:1 numbers.
- Draw the wheel pitch circle with C (circle) at centre
0,0, radius40(d₂ = 80), and the outside circle radius42(da2 = 84). - Locate the worm axis at centre distance a = 50 by drawing a guide line with L from
0,0to-50,0; the end is the worm axis. - Draw the worm pitch circle with C at the axis end, radius
10(d₁ = 20) — it touches the wheel pitch circle exactly, since 40 + 10 = 50 = a. - Draw the worm side view with REC (rect) as a bar along the axis, then the thread lines with L leaning at the 5.71° lead angle, repeated every axial pitch px = 6.283 with AR (array).
- Check the centre distance and diameters with ME (measure) before dimensioning.
- Dimension the centre distance a, wheel Ø and worm Ø with DLI (dimension linear).
For a full set of wheel teeth, draft one tooth and PO (polar array) it around the wheel centre 40 times, equal to z₂.
Frequently asked questions
how to calculate worm gear ratio
Ratio = wheel teeth ÷ worm starts. A 40-tooth wheel with a single-start worm gives 40:1; a two-start worm on the same wheel gives 20:1.
how to find worm gear lead angle
Lead angle γ = arctan(worm starts ÷ diameter factor q). For z₁ = 1 and q = 10 that is arctan(1÷10) = 5.71°.
when is a worm gear self-locking
Usually when the lead angle is low, roughly below 5–6° — the wheel cannot back-drive the worm. That suits hoists that must hold a load, but it lowers transmission efficiency.
how to calculate worm gear centre distance
Centre distance a = (worm pitch dia + wheel pitch dia) ÷ 2. For d₁ = 20 and d₂ = 80 that gives a = 50 mm.
Summary
A worm gear is calculated from the module m, worm starts z₁ and wheel teeth z₂: ratio = z₂ ÷ z₁, wheel pitch dia = z₂ × m, worm pitch dia = q × m, lead angle = arctan(z₁ ÷ q), centre distance = (d₁ + d₂) ÷ 2. The 40:1 example gives d₁ = 20, d₂ = 80, a = 50 mm and a 5.71° lead angle. Draw two pitch circles touching at distance a, dimension with DLI, and verify every value with ME before manufacture.