Home / Articles / Sine bar setup: gauge-block height from the angle
Draw + calculate · Production

Sine bar setup: gauge-block height from the angle

6 min read · updated 19 Nov 2026

A sine bar is the most accurate shop tool for setting an angle. It uses one piece of trigonometry: two rollers at the ends of the bar sit a known distance L apart, and lifting one end on a stack of gauge blocks of height H tilts the bar to angle θ, where H = L × sin θ. This guide gives the formula, a worked 100 mm bar example, a stack-height table every 5°, how to solve back for the angle, and how to check the triangle in DXCAD2D.

The right triangle of a sine bar

The distance between the two roller centres is the hypotenuse (L); the gauge-block stack is the side opposite the angle θ (H). When one end is lifted, the bar makes angle θ with the surface plate, where sin θ = H ÷ L, which gives the height to stack.

θ H L gauge stack H surface plate
Two rollers a distance L apart · the right end lifted by a gauge stack of height H · the bar tilts to angle θ where H = L × sin θ

The formulas

Stack height from the angle: H = L × sin θ
Angle from a measured height: θ = arcsin (H ÷ L)
L is the distance between roller centres (usually 100 mm, or 5 inch = 127 mm)

A metric sine bar has L = 100 mm, which makes the maths easy: H = 100 × sin θ reads straight off in millimetres. Inch bars are usually 5 inch (127 mm).

Worked example — a 100 mm bar

Set 30°: H = 100 × sin 30° = 100 × 0.5 = 50.000 mm → stack gauge blocks to exactly 50 mm.

Set 15°: H = 100 × sin 15° = 100 × 0.258819 = 25.882 mm → build a stack such as 25 + 0.8 + 0.08 + 0.002 to make 25.882.

Solve back: if the stack under a 100 mm bar is 42.262 mm → θ = arcsin (42.262 ÷ 100) = arcsin 0.42262 = 25.00°

Watch out: stack height does not grow linearly with angle — it follows a sine. Going 0° → 5° needs 8.716 mm, but 40° → 45° adds only 6.432 mm more. The steeper the angle, the more sensitive it is to error, so sine bars are normally used up to about 45°.

Stack-height table (100 mm bar)

Angle θH = 100·sin θ (mm)Angle θH = 100·sin θ (mm)
5°8.71630°50.000
10°17.36535°57.358
15°25.88240°64.279
20°34.20245°70.711
25°42.262——

For a 127 mm (5 inch) bar, multiply sin θ by 127 instead: e.g. 30° → 127 × 0.5 = 63.5 mm.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Check the angle triangle in the program

Before building the real gauge stack, draw the right triangle in DXCAD2D to confirm H and θ (for a 100 mm bar at 30°: base = 100·cos 30° = 86.6, height H = 50, hypotenuse = L = 100).

  1. Press L, click the start point, type 86.6,0 and press Enter → the base (L·cos θ).
  2. From the right end press L, type 0,50 and press Enter → the vertical equal to the stack height H.
  3. Press L and draw from the top point back to the start → this hypotenuse is the sine-bar line.
  4. Press ME and measure the hypotenuse — it should read 100.0 (= L) and the vertical 50 (= H), confirming the 30° angle.
  5. Press D and dimension all three sides to turn it into a setup drawing for the shop.

Frequently asked questions

How does a sine bar calculate the gauge-block height

With H = L × sin θ, where L is the roller-centre distance (usually 100 mm). To set 30° on a 100 mm bar you stack gauge blocks to 100 × sin 30° = 50 mm.

What gauge-block stack sets 30 degrees on a 100 mm sine bar

Exactly 50 mm, because H = 100 × sin 30° = 100 × 0.5 = 50 mm — an easy value to remember and a common one for checking tools.

How do I find the angle from the stack height

Use θ = arcsin (H ÷ L). For a 42.262 mm stack on a 100 mm bar that is arcsin 0.42262 = 25°. You must know the bar length L first.

Why is a sine bar poor for very large angles

Because height follows a sine: as the angle nears 90° the sine curve flattens, so a small gauge-block error turns into a larger angle error. In practice sine bars are kept to about 45° or less.

What is the difference between a 5 inch and a 100 mm sine bar

Only the length L: a 5 inch bar is 127 mm, a metric bar is 100 mm. Same formula, just change L — so 30° on a 127 mm bar needs a 63.5 mm stack.

Summary

A sine bar turns an angle into a height you can measure precisely with one formula, H = L × sin θ. A 100 mm bar is easiest because H = 100 × sin θ: 30° needs 50 mm, 15° needs 25.882 mm. Solve back with θ = arcsin(H ÷ L), and avoid angles beyond about 45° because of the sine's sensitivity. Drawing the triangle in DXCAD2D and measuring it with ME/D confirms the setup before you build the real gauge stack.