Home / Articles / Calculate and draw a taper — ratio and angle
Draw + calculate · 2D drafting

Calculate and draw a taper — ratio and angle

7 min read · updated 15 Nov 2026

A taper is a part whose diameter changes steadily along its length — found on drill shanks, tapered shafts, plug gauges and press fits. Drawing a taper means converting correctly between three things: the taper ratio (e.g. 1:20), the taper per side and the angle (half angle and included angle). Once you can convert, you can draw the taper line accurately in DXCAD2D Online. This guide gives the formulas, a standard-taper table, a worked example and the drawing steps.

Definitions and formulas

Let D = large-end Ø, d = small-end Ø, and L = the axial length between the two ends. They are all linked as follows.

Taper ratio (on diameter): T = (D − d) ÷ L  |  Taper per side: (D − d) ÷ (2L)  |  Half angle: α = atan((D − d) ÷ (2L))  |  Included angle: 2α

The common slip is to confuse "on diameter" with "per side". The taper angle is measured from the axis to the surface, so it uses the taper per side (divide by 2L), not the full ratio.

α D d L centreline (axis)
Taper: D is the large end · d the small end · L the length · α the half angle from the axis to the surface (included angle = 2α).

Worked example: a shaft tapering D 50 → d 40 over 100

A shaft tapers from large end D = 50 mm to small end d = 40 mm over an axial length L = 100 mm.

FindFormulaSubstituteResult
Taper ratio (on Ø)T = (D − d) ÷ L(50 − 40) ÷ 1000.1 = 1:10
Taper per side(D − d) ÷ (2L)10 ÷ 2000.05
Half angleα = atan(0.05)atan(0.05)2.862° (2°51.7′)
Included angle2α2 × 2.862°5.725° (5°43.5′)

Check it back: if the drawing gives d = 40, L = 100 and a 1:10 taper, then D = d + L ÷ K = 40 + 100 ÷ 10 = 50 mm — matching the problem.

Common standard tapers

A taper ratio 1:K means the diameter changes 1 unit per K units of length. Half angle = atan(1 ÷ (2K)).

Taper ratioTaper on Ø (per unit)Half angle αIncluded angle 2α
1:100.10002.862°5.725°
1:200.05001.432°2.864°
1:300.03330.955°1.910°
1:500.02000.573°1.146°
Inch units (TPF): some shops use "taper per foot" = taper on Ø × 12, e.g. 1:10 = 0.1 in/in = 1.2 in per foot. The angle is unchanged.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Drawing the taper line in DXCAD2D Online

  1. Press L and draw a horizontal centreline L = 100 mm long for reference.
  2. At the large end offset the centreline up by D ÷ 2 = 25 mm, and at the small end up by d ÷ 2 = 20 mm, to get the two top corner points.
  3. Press L or P and draw the surface line from the large-end point to the small-end point (this line sits at the half angle α = 2.862°).
  4. Use mirror to reflect the surface across the centreline for the lower face, then close the ends with L.
  5. Press M to check the two end diameters and the angle, then D to dimension D, d, L and note the 1:10 ratio or the 5.725° included angle.
Tip: a taper drawing should state either the "taper ratio" or the "included angle" clearly, plus one reference Ø and the length. The turner can then set the compound/tool angle exactly without guessing.

Frequently asked questions

What angle is a 1:20 taper

Half angle = atan(1 ÷ 40) = 1.432°, included angle = 2.864°, because 1:20 means the diameter changes 1 unit per 20 units of length.

What is the difference between taper on diameter and taper per side

Taper on Ø = (D − d)/L counts both sides; taper per side = (D − d)/(2L) counts one side. The surface angle uses taper per side, since it is measured from the axis to the surface.

How do I find the large diameter from the small end and the ratio

D = d + L ÷ K for a 1:K taper, e.g. d 40, length 100, 1:10 gives D = 40 + 100 ÷ 10 = 50 mm.

Should I use the half angle or the included angle

The half angle (α) is from the axis to one surface — use it to set the lathe compound. The included angle (2α) is the full cone angle across both sides and is usually what the drawing calls out.

How do I measure a taper on the part

Measure the Ø at two points a known axial distance L apart, then T = (D − d)/L gives the actual taper ratio to compare with the drawing.

Summary

A taper converts through one pair of formulas: taper ratio T = (D − d)/L and half angle α = atan((D − d)/(2L)), with included angle = 2α. The D 50 → d 40 over 100 example gives a 1:10 ratio, 2.862° half angle and 5.725° included angle. Remember the angle uses "taper per side" (divide by 2L), and find a missing diameter with D = d + L/K. With the numbers set, draw the surface line in DXCAD2D Online using offset, line and mirror, and dimension it with dim — ready for the shop.