Draw & calculate a dovetail + over-pins measurement
A dovetail is the trapezoidal tongue/groove used as a sliding way that locks and can't lift out the top. You can't measure a dovetail directly with a caliper because the sharp corners are angled, so machinists set two gauge balls or rods against it and measure over them (over pins). This guide covers both calculating the top and bottom widths from the angle and depth for drawing, and the over-pins formula for inspecting a real part, with every number worked out.
Dovetail geometry: angle, depth, width
A dovetail is set by three values: the flank angle α (the sloped face relative to the base, commonly 60°), the depth H, and the wide-side width B (the base). Each sloped face moves in horizontally by:
Narrow-side width = B − 2 · run (for a tongue wider at the bottom), or = B + 2 · run going from the narrow side to the wide side.
Worked example: dovetail layout
Design a dovetail tongue with α = 60°, depth H = 12 mm, wide side (base) B = 40 mm. Find the narrow (top) width.
- run = H ÷ tan 60° = 12 ÷ 1.7320 = 6.928 mm per side
- Top width = B − 2 · run = 40 − 2(6.928) = 40 − 13.856 = 26.14 mm
That gives every coordinate for the section: the two bottom corners 40 apart, the two top corners 26.14 apart, 12 high.
Inspect with two balls (over pins)
Set two gauge balls/rods of diameter d against the two bottom corners of the tongue (each ball touches a sloped face and rests on the base plane), then measure across the outside of both balls to get M.
Over-pins formula (male dovetail, wider at bottom):
where M = distance over pins, B = base (wide) width, d = ball diameter, α = flank angle from the base.
Worked example: a dovetail tongue B = 40 mm, α = 60°, with balls d = 10 mm.
- tan(α/2) = tan 30° = 0.57735
- 1 + tan(α/2) = 1.57735
- M = 40 + 10 × 1.57735 = 40 + 15.774 = 55.77 mm
Measure 55.77 within tolerance and it passes. To check the base width back out, use B = M − d(1 + tan(α/2)) = 55.77 − 15.77 = 40.00 mm.
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineDraw the dovetail in the program
Use the coordinates from the layout above (B = 40, top = 26.14, depth 12), with the bottom-left corner at (0,0).
- Type P (polyline) and press Enter.
- Bottom-left
0,0Enter → bottom-right#40,0Enter → top-right#33.072,12Enter → top-left#6.928,12Enter → close back to the first point. - (33.072 = 40 − 6.928 and 6.928 = run.) That is the tongue, wider at the bottom.
- Check the angle: type D (dim) across the base and a flank — it should read 60° — and M (measure) to confirm the 12 depth and 26.14 top width.
- For the mating groove, offset or redraw the inverse, then mirror if you need a matched pair.
Frequently asked questions
How do I measure a dovetail with balls
Set two gauge balls against the bottom corners of the tongue and measure over the outside: M = B + d(1 + tan(α/2)), where B = base width, d = ball size, α = flank angle.
Dovetail 60 degrees, 12 deep, base 40 — what is the top width
run = 12 ÷ tan60 = 6.928 per side, so the top width = 40 − 2(6.928) = 26.14 mm.
Why measure a dovetail with balls instead of directly
The sharp dovetail corners are angled and usually broken, so a caliper has no definite point to read. Balls touch only the sloped faces, which lets you calculate the real size back out.
Does a female dovetail groove use the same formula
No — a female groove is measured between the two balls: M = W − d(1 + cot(α/2)), where W = floor width. The male over-pins case uses tan instead of cot.
Summary
A dovetail has two jobs: drawing and measuring. To draw, find run = H · cot α, then the narrow width = base − 2·run. To inspect, measure over two balls and compare with M = B + d(1 + tan(α/2)), or solve back with B = M − d(1 + tan(α/2)). Remember that the male (over pins) uses tan(α/2) while the female (between pins) uses cot(α/2), and you can always verify the formula with the α = 90° case, which must give M = B + 2d.