How to calculate and draw a knurl — pitch and allowance
A knurl is the raised grip pattern on a handle or knob. To make it come out clean and track (line up instead of double-cutting) you have to calculate two things: the number of teeth around the circumference must come out whole, and you must turn the blank undersize before knurling because rolling the pattern pushes metal up and the diameter grows. This guide gives the formulas, a worked example and how to draw a diamond knurl on a drawing.
Knurl pitch
The pitch is the distance between two tooth crests measured around the circumference. The metric system (DIN 82) sets standard pitches in millimetres, while inch knurling wheels are often given as a diametral pitch (DP) — 64, 96, 128 DP. Convert DP to a circular pitch with p = 25.4 × π ÷ DP.
| Circular pitch p (mm) | Use | Nearest inch DP |
|---|---|---|
| 0.5 – 0.6 | Fine, small knobs | 128 DP (0.62) |
| 0.8 | Medium, general handles | 96 DP (0.83) |
| 1.0 – 1.2 | Medium-coarse | — |
| 1.6 | Coarse, large grips | 64 DP (1.25) is coarser |
Making it track: the teeth count must be whole
A diamond knurl is rolled by a wheel that presses again every revolution of the work. If the circumference does not divide evenly by the pitch, the next revolution misses the first tracks and the pattern smears (double-tracking). The condition is that the number of teeth around the circumference must be a whole number.
Worked example: Ø20 handle, pitch 0.8
You want a diamond-knurled handle about Ø20 mm using a p = 0.8 mm wheel.
Step 1 — teeth count: N = π × 20 ÷ 0.8 = 62.83 ÷ 0.8 = 78.54, which is not whole, so the pattern will not track at exactly Ø20.
Step 2 — round the teeth count: choose N = 78 → the tracking diameter D = 78 × 0.8 ÷ π = 62.4 ÷ 3.1416 = 19.86 mm (N = 79 would give 20.12 mm).
Step 3 — allow for swell: knurling pushes the surface up by roughly a third of the pitch ≈ 0.8 ÷ 3 = 0.27 mm, so turn the blank smaller than that: pre-knurl ≈ 19.86 − 0.27 = about 19.6 mm. Test on an offcut of the same material, measure, then adjust — the swell depends on material and pressure.
| Step | Value |
|---|---|
| Target finished size | ≈ Ø20 mm |
| Teeth count N = πD/p | 78.54 (not whole) |
| Chosen whole N | 78 |
| Tracking Ø = Np/π | 19.86 mm |
| Swell allowance ≈ p/3 | 0.27 mm |
| Turn blank to ≈ | 19.6 mm (test and adjust) |
Drawing a knurl on a drawing
You do not draw every tooth — a knurl is shown as a cross-hatched band with a note giving the type and pitch.
- Type REC and draw the side view of the cylindrical part, then use L to draw two vertical lines marking the band edges (or O to offset them from the ends).
- Show the diamond with cross-hatching: type H, pick the band area and set a crossed (diamond) pattern, or draw one set of 30° lines with L, AR array them across the band, then MI mirror a second set the other way so they cross.
- Add a leader note with LE giving the spec, e.g. "DIAMOND KNURL 0.8 PITCH, RAISED".
- Dimension with D: give the finished diameter after knurling and the band length (do not dimension the pre-knurl size — the machinist allows for that).
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineShop tips
A straight knurl uses the same whole-teeth condition but is easier because the lines run along the axis and cannot smear revolution to revolution. A diamond knurl is the one to watch for tracking. If adjusting the pre-knurl size is awkward on the job, the other route is to press harder so the teeth roll deep enough to lock in — but always start from the calculated diameter.
Frequently asked questions
how much undersize before knurling
Turn the blank about one third of the pitch under the finished size (≈ 0.3p) because knurling swells the surface. For pitch 0.8 that is about 0.27 mm — test on an offcut first, then adjust.
how to calculate the number of knurl teeth
N = π × diameter ÷ pitch, then round N to a whole number so the pattern tracks without smearing. Back-solve the diameter that tracks with D = Np ÷ π.
why is my knurl double-tracking
Because the circumference does not divide evenly by the pitch, so the wheel misses the previous tracks on the next revolution. Fix it by adjusting the pre-knurl diameter until N is a whole number, or press harder so the teeth lock in.
how to convert DP to a mm knurl pitch
Circular pitch p (mm) = 25.4 × π ÷ DP. So 96 DP ≈ 0.83 mm, 128 DP ≈ 0.62 mm and 64 DP ≈ 1.25 mm.
Summary
A good knurl comes down to two values: make the teeth count N = πD ÷ p a whole number so the pattern tracks, and turn the blank undersize by about a third of the pitch because the surface swells. For a Ø20 handle at pitch 0.8, choose N = 78, which gives a tracking Ø of 19.86 mm, then turn the blank to about 19.6 mm. On a drawing, show it as a cross-hatched band and dimension the finished size and band length with a pitch note.