Home / Articles / Calculate and draw drill point length for 118°/135°
Draw + calculate · Trade

Calculate and draw drill point length for 118°/135°

7 min read · updated 20 Nov 2026

A drill has a conical point, not a flat end, so when you work out drilling depth or draw a section through a hole you must add the "point length" — above all when you need the hole at full diameter down to a set level, or when drilling right through a plate so the tip breaks out. This guide gives the formula for point length at the common 118° and 135° angles, a table of values by drill size, and the steps to draw a correct drilled-hole section in DXCAD2D.

The point-length formula

A drill point is a cone with an included (full) point angle A (the angle between the two cutting lips, e.g. 118° or 135°); the half angle = A/2 measured from the drill axis. The point length (from the shoulder where the hole reaches full diameter down to the sharp tip) is

Point length = (Ø ÷ 2) ÷ tan(A ÷ 2)
Ø = drill diameter · A = full point angle · at 118° this is ≈ 0.300·Ø · at 135° it is ≈ 0.207·Ø
Ø point full Ø depth A full point angle A (118° or 135°)
Section through a drilled hole: above the shoulder it is full Ø, the point is a cone of angle A, and its length = (Ø/2)/tan(A/2).

A worked example with real numbers

Problem: a Ø10 mm drill with a 118° point. Find the point length and the depth to drill so the hole is full Ø10 for 20 mm.

Half angle = 118 ÷ 2 = 59° → tan 59° = 1.6643

Point length = (10 ÷ 2) ÷ 1.6643 = 5 ÷ 1.6643 = 3.00 mm

To get full Ø10 for 20 mm (measured to the shoulder), the sharp tip goes 3.00 mm deeper, so you must drill until the tip is at = 20 + 3.00 = 23.0 mm.

With a 135° point (half angle 67.5°, tan 67.5° = 2.4142) the point length = 5 ÷ 2.4142 = 2.07 mm — shorter, because the angle is blunter.

Through holes: for a full-Ø hole right through a plate of thickness t, the tip must break out by at least the point length. A 20 mm plate with a Ø10 118° drill needs the tip driven to ≥ 23 mm total so the hole is full diameter all the way through.

Factor table by angle and drill size

The point-length factor = 0.5 ÷ tan(A/2); multiply it by Ø for the point length.

Point angle AHalf angleFactor × Ø
90°45°0.500
118° (general)59°0.300
130°65°0.233
135° (hard steel / stainless)67.5°0.207
140°70°0.182
Drill Ø (mm)Point at 118° (mm)Point at 135° (mm)
51.501.04
61.801.24
82.401.66
103.002.07
123.612.49
164.813.31
206.014.14

Drawing a drilled-hole section in DXCAD2D

Draw a section through a Ø10 hole, 20 mm full depth, 118° point, with the hole axis at x = 0 and the top face at y = 0 (depth is negative going down).

  1. Type REC and press Enter, draw the cylindrical part (full Ø) from corner #-5,0 to #5,-20 — width Ø10, depth 20 mm.
  2. Type L and press Enter, draw the right cone lip from the shoulder #5,-20 to the tip on the axis #0,-23 (depth 20 + point length 3).
  3. Type MI, select the cone lip, and mirror it about the hole axis (x = 0) to get the symmetrical left lip.
  4. Type D to dimension Ø10 at the mouth, the 20 mm full depth, and the 118° point angle at the tip; type ME to measure the point length and confirm it is 3.0 mm.
Check the angle: each cone lip sits at 59° to the drill axis (half of 118°). From a shoulder 5 mm off the axis down to a tip 3 mm deeper, atan(5 ÷ 3.0) = 59° exactly.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Why drilled holes are not flat-bottomed

Because the drill point is a cone, an ordinary drilled hole always has a conical bottom. For a flat bottom you need a flat/centre drill or an end mill pass. When a drawing calls out a hole depth, state clearly whether it is the "full Ø depth" (to the shoulder) or "including the point" — they differ by exactly the point length you calculated.

Frequently asked questions

how long is a 118 degree drill point

About 0.3 times the diameter: a Ø10 drill has a 3.0 mm point, a Ø20 drill a 6.0 mm point (from (Ø/2)/tan 59°).

what is the difference between 118 and 135 degree drills

118° suits general work and has a sharper, longer point (0.3·Ø); 135° is blunter, better for hard steel and stainless, with a shorter point (0.207·Ø) and often a non-skating split point.

how much extra depth to drill through a plate

Allow at least the point length so the full Ø breaks through. A 20 mm plate with a Ø10 118° drill needs the tip driven to ≥ 23 mm total.

why is a drilled hole not flat on the bottom

Because the drill point is a cone set by the point angle, so the hole bottom is always conical. For a flat bottom use a flat/centre drill or an end mill.

Summary

Drill point length comes from (Ø/2)/tan(angle/2): about 0.3·Ø at 118° and 0.207·Ø at 135°. A Ø10 118° drill has a 3.0 mm point, which you must always add when you need full Ø depth or a through hole. Draw the hole section in DXCAD2D with REC for the full-diameter part and cone lips from shoulder to tip, mirrored about the axis — and remember a drilled hole bottom is always conical.