Countersink depth from the 82° / 90° angle
A countersink is the cone a flat-head screw sits into so its head finishes flush with the surface. The key question is how deep to plunge to get the top diameter you want. Once you know the cutter angle (82°, 90°, 100°…) and the top diameter and the pilot-hole diameter, the depth falls straight out of the cone geometry. This guide gives the formula, a worked M6 flat-head example and how to draw the section in the program.
The cone geometry of a countersink
A countersink is a cone of included angle α, so its surface makes half that angle (α ÷ 2) with the vertical axis. Drop a vertical depth h and the radius grows by h × tan(α ÷ 2). So the depth between the top (diameter D) and the pilot hole (diameter d) is
where D = top diameter, d = pilot-hole diameter, α = included cone angle
Rearrange to find the top diameter at any depth: D = d + 2 × h × tan(α ÷ 2).
The cot(α/2) factor for each angle
Drop cot(α/2) straight in for the standard cutter angles.
| Included angle α | Used for | cot(α/2) |
|---|---|---|
| 60° | Lead-in / centre holes | 1.7321 |
| 82° | Inch flat-head screws (UNC/UNF) | 1.1504 |
| 90° | Metric flat-head screws (DIN 965) | 1.0000 |
| 100° | Aerospace flat-head screws | 0.8391 |
| 120° | Rivet-hole chamfers | 0.5774 |
Worked example: M6 flat-head screw (90°)
A metric M6 flat-head screw has a 90° head. With a clearance hole of Ø6.6 mm and a wanted top diameter D = 12.6 mm so the head sits flush:
h = (12.6 − 6.6) ÷ 2 × cot(45°) = 6.0 ÷ 2 × 1.0 = 3.0 mm → plunge the countersink 3.0 mm deep.
82° inch example: a 1/4" flat-head screw, 82° head, pilot Ø6.8, top D = 13.0
h = (13.0 − 6.8) ÷ 2 × 1.1504 = 3.1 × 1.1504 = 3.57 mm.
Check in reverse: a 90° countersink 3.0 mm deep from a Ø6.6 hole gives D = 6.6 + 2 × 3.0 × tan 45° = 6.6 + 6.0 = 12.6 mm — back to the set value.
Drawing the section in the program
- Type L and draw a vertical centreline for reference plus the horizontal top surface of the material.
- Draw the pilot-hole walls: two vertical lines each d ÷ 2 = 3.3 mm from the centre (type coordinates such as
3.3,0to3.3,-15). - Draw the cone surface: from the top edge at
6.3,0draw L down to meet the hole wall at3.3,-3.0(depth h = 3.0) — one cone flank. - Type MI and mirror the cone flank and hole wall about the centreline to get the symmetric other side.
- Dimension with D: the top diameter D at the surface, the pilot hole d, and the included angle α (or give the depth h instead of the angle). Add section hatching with H for a full section view.
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineWatch out
The top diameter D must be a little wider than the actual screw head for the head to finish flush — read D from the screw's own table (DIN 965 for metric). And the countersink angle must match the screw-head angle (metric 90°, inch usually 82°). If the angles do not match, the head touches on a narrow ring, clamps poorly and can distort the countersink.
Frequently asked questions
how to calculate countersink depth
Depth h = (top diameter − pilot hole) ÷ 2 × cot(included angle ÷ 2). The 90° case is easiest because cot(45°) = 1, so the depth equals half the diameter difference.
difference between 82 and 90 degree countersink
82° suits inch flat-head screws (UNC/UNF); 90° suits metric flat-head screws (DIN 965). Match the countersink angle to the screw-head angle so the head seats flush.
how deep to countersink for a flush screw head
Deep enough that the top is a little wider than the screw head: use h = (D − d) ÷ 2 × cot(α/2). For M6 at 90° with a Ø12.6 top and Ø6.6 hole that is 3.0 mm.
can I get the top diameter from the depth
Yes, rearrange to D = d + 2 × h × tan(α ÷ 2). For 90° a 3 mm-deep cut from a Ø6.6 hole gives a 12.6 mm top diameter.
Summary
Countersink depth comes straight from the cone: h = (D − d) ÷ 2 × cot(α ÷ 2). The 90° angle is easiest because h = (D − d) ÷ 2 exactly. For an M6 at 90° with a Ø12.6 top and Ø6.6 hole the depth is 3.0 mm. Draw the section from the hole walls and cone flanks, mirror it for symmetry, dimension the top, hole and angle — and always match the countersink angle to the screw-head angle.