Home / Articles / How to draw a fillet and a chamfer
How to draw · 2D drafting

How to draw a fillet and a chamfer

7 min read · updated 8 Nov 2026

Metal part corners are almost never left truly sharp. We break them two ways: a fillet, which replaces the corner with an arc of radius R, and a chamfer, which cuts the corner off as an angled face of size C. This guide explains the difference, how each is dimensioned, where the correct tangent points are, and how to draw both with the fillet and chamfer commands in DXCAD2D.

Fillet vs chamfer: what's the difference

A fillet is a rounded corner set by a radius R (e.g. R3 = 3 mm radius). The arc is tangent to both edges so the transition is smooth. Fillets are used on internal corners to reduce stress concentration and to let material flow in castings and pressings.

A chamfer is an angled flat cut set by a distance C, which by default means a C×45° face (e.g. C2 = cut 2 mm deep at 45°). Chamfers deburr and break sharp edges for safety, and give a lead-in when assembling a shaft into a hole or starting a tap.

Quick memory aid: fillet = rounded corner, given as R · chamfer = angled cut, given as C. Loaded internal corners usually get a fillet; outer edges that need breaking usually get a chamfer.
R fillet (round) C C chamfer (bevel)
Left: a fillet replaces the corner with an arc of radius R · Right: a chamfer cuts the corner to an angled face of size C on each edge (C×45°).

How they are dimensioned

SymbolMeaningExample
R3fillet, 3 mm radiusrounded corner, radius 3
C2chamfer, 2 mm × 45°cut 2 deep both sides, 45°
2 × 45°long form of C22 mm distance, 45° angle
2 × 30°non-45° chamfer2 mm on one side, 30° angle

A non-45° chamfer must always give two values — "distance × angle" or "distance × distance" — because one number alone cannot define it. The C2 shorthand only applies to a 45° chamfer where both legs are equal.

Chamfer face length: a C×45° chamfer has a cut face of length C × √2, e.g. C3 → 3 × 1.4142 = 4.243 mm. Use this when working out cut length or surface area.

Drawing a fillet with the right tangent points

The point of a fillet is an arc that is tangent to both edges, so its centre must sit exactly R from each line. For a 90° corner this is easy.

  1. Put the corner at (0,0) with one edge along the X axis and the other along the Y axis.
  2. The arc centre is at (R, R); the tangent points are (R, 0) on the X axis and (0, R) on the Y axis.
  3. For an R5 fillet on a square corner: centre (5,5), tangent points (5,0) and (0,5), and the arc sweeps 90°.

In DXCAD2D you don't have to work this out. Press fillet, enter the radius R, then click the two edges that meet — the program trims them to the tangent points and places the arc automatically.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Drawing a chamfer with the right setback

A chamfer cuts the corner off as an angled face, starting a distance C from the corner on each edge. For a C×45° chamfer on a square corner:

  1. Put the corner at (0,0) with edges along the X and Y axes.
  2. The cut points are (C, 0) and (0, C); the line between them is the 45° chamfer face.
  3. For C3: cut points (3,0) and (0,3), and the face is 3√2 = 4.243 mm long.

In DXCAD2D press chamfer, enter the setback (equal both sides for 45°, or two values for another angle), then click the two edges. To draw it by hand, use L and type the two cut-point coordinates.

Watch out: R or C can't be larger than the edge it sits on. A 4 mm long edge can't take an R5 fillet, because the tangent point would fall past the end of the line. Reduce the radius or extend the edge first.

Choosing a fillet or a chamfer

Use a fillet on loaded internal corners — the arc spreads stress better than a sharp corner, reduces cracking, and is needed in castings and mouldings so material flows. Use a chamfer on outer edges to break sharp edges, prevent cuts, and ease assembly of a shaft into a hole or the mouth of a tapped hole. On laser and plasma parts, outer corners often get a small fillet to avoid heat build-up at a sharp point.

Frequently asked questions

What is the difference between a fillet and a chamfer

A fillet rounds the corner with an arc given by a radius R; a chamfer cuts the corner to a flat angled face given by a distance C (usually C×45°). Fillets reduce stress on internal corners, chamfers break edges and help assembly.

What does C2 mean on a drawing

A chamfer cut 2 mm deep at 45°, equal on both sides — the same as writing 2 × 45°.

How long is a 45 degree chamfer face

The face length = C × √2, so C2 is 2.828 mm and C3 is 4.243 mm. Use this value for cut length.

What fillet radius should I use

It depends on the part, but loaded internal corners should use the largest R the design allows to cut stress, while cosmetic or edge-breaking fillets are usually small, R1–R3. Follow the drawing or part standard.

Why won't my fillet apply

Usually because the radius R is larger than the edge being filleted, so the tangent point falls past the line's end. Reduce the radius or extend the edges first.

Summary

A fillet replaces a corner with an arc of radius R, tangent points sitting R from each edge (centre at R,R for a square corner). A chamfer cuts the corner to an angled face of size C, with cut points C from the corner on each edge, and a C×45° face is C√2 long. In DXCAD2D, use the fillet and chamfer commands and click the two edges to trim them exactly. Choose a fillet on loaded internal corners and a chamfer on outer edges for deburring and assembly.