Home / Articles / Draw and calculate Acme / Tr trapezoidal power-screw threads
Draw + calculate

Draw and calculate Acme / Tr trapezoidal power-screw threads

8 min read · updated 18 Nov 2026

Trapezoidal threads drive power screws — jacks, vice spindles, lathe lead screws — because the trapezoidal tooth carries axial load well and is easier to cut than a square thread. The metric system calls it Tr, with a 30° included thread angle; the inch system calls it Acme, with a 29° angle. This guide gives the formulas for every dimension, a worked Tr 30×6 example, and the steps to draw the tooth profile in DXCAD2D Online.

Key dimensions of a metric trapezoidal (Tr) thread

A Tr d×P thread is written with d = major (outside) diameter and P = pitch (crest-to-crest). The values you need are:

DimensionFormula (ISO 2901 / DIN 103)
Clearance ac0.25 (P 1.5–5) · 0.5 (P 6–12) · 1 (P ≥ 14)
Screw thread depth h₃0.5P + ac
Screw minor dia d₃d − 2h₃
Pitch dia d₂d − 0.5P
Nut minor dia D₁d − P
Nut major dia D₄d + 2ac
Lead (single start)P (multi-start = n × P)
Pitch vs lead: pitch P is the distance between two adjacent crests; lead is how far the screw advances in one turn. A single-start thread has lead = P; a two-start thread has lead = 2P, so one turn of the handle advances further when the thread is multi-start.
pitch P h₃ included angle 30° (Tr) / 29° (Acme) pitch line
Trapezoidal tooth profile in axial section: flanks lean 15° per side (30° total); at the pitch line the tooth thickness equals the groove = P/2.

Worked example: Tr 30 × 6, single start

Trapezoidal screw, major d = 30 mm, pitch P = 6 mm. A pitch of 6 falls in the 6–12 band, so ac = 0.5.

DimensionSubstituteResult
Thread depth h₃0.5×6 + 0.53.5 mm
Screw minor dia d₃30 − 2×3.523.0 mm
Pitch dia d₂30 − 0.5×627.0 mm
Nut minor dia D₁30 − 624.0 mm
Nut major dia D₄30 + 2×0.531.0 mm
Tooth thickness at pitch lineP ÷ 23.0 mm
Crest flat width (approx)0.366 × P2.20 mm

Lead angle (to check power transmission) λ = arctan( lead ÷ (π × d₂) ) = arctan( 6 ÷ (π × 27) ) = arctan(0.0707) = 4.05°. A lead angle this low tends to be self-locking (the screw does not back-drive when released), which suits a jack.

Where the crest width comes from: at the pitch line the tooth is P/2 = 3.0 thick. Going up to the crest (a rise of P/4 = 1.5) with 15° flanks per side, the thickness drops by 2×1.5×tan15° = 0.80, leaving a 3.0 − 0.80 = 2.20 mm crest flat.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Drawing the tooth profile in DXCAD2D

Draw one tooth in axial section, then repeat it along the pitch. Using the Tr 30×6 numbers, put the minor-diameter line (d₃/2 = 11.5) at y = 0.

  1. Draw the minor-diameter line with L (line), horizontal at y = 0, as the tooth base.
  2. Build one tooth with PL (polyline), typing relative coordinates up the 15° flanks: thread depth h₃ = 3.5, so each flank runs 3.5×tan15° = 0.94 mm along the axis and the crest flat is 2.20 wide → @0.94,3.5 (up the left flank) @2.20,0 (crest) @0.94,-3.5 (down the right flank).
  3. Check the angle with ME (measure), or confirm the flank is 15° from vertical (75° from horizontal).
  4. Repeat the tooth along the axis with AR (array), pitch spacing = 6 mm, count to suit the thread length.
  5. Draw the major-diameter line (major 30 → radius 15 from the axis) and pitch line (d₂ = 27 → 13.5) with O (offset) from the axis to control depth.
  6. Dimension the pitch, depth and minor diameter with DLI (dimension linear).

To draw the nut, flip the profile (the nut groove receives the screw tooth) using nut major D₄ = 31 and nut minor D₁ = 24 as limits, then MI (mirror) the profile to the other side of the axis.

Frequently asked questions

what is the minor diameter of a tr 30x6 thread

Screw minor diameter d₃ = 30 − 2×(0.5×6 + 0.5) = 23.0 mm. The pitch diameter d₂ = 27.0 mm and the nut minor diameter D₁ = 24.0 mm.

what is the acme thread angle

Metric Tr threads have a 30° included angle (15° per flank); inch Acme threads have a 29° included angle (14.5° per flank).

how to calculate trapezoidal thread depth

Screw thread depth h₃ = 0.5×pitch + clearance. The clearance is 0.25 (pitch 1.5–5), 0.5 (pitch 6–12) or 1 (pitch ≥ 14). For Tr 30×6 that gives h₃ = 3.5 mm.

what is the difference between acme and tr threads

The sections look alike but the angle differs: Tr is metric at 30°, Acme is inch at 29°. The main formulas are the same — you just change the flank angle and work in inches/TPI for Acme.

Summary

A trapezoidal power-screw thread comes from the pitch P and clearance ac: thread depth h₃ = 0.5P + ac, screw minor = d − 2h₃, pitch dia = d − 0.5P. For Tr 30×6 that gives d₃ = 23, d₂ = 27, D₁ = 24 and a 4.05° lead angle. Draw one tooth with PL along 15° flanks, array it at the 6 mm pitch, and verify every value with ME before cutting.