Home / Articles / How to draw a tangent arc with the fillet command
How to draw · Basics

How to draw a tangent arc with the fillet command

7 min read · updated 10 Nov 2026

A tangent arc is an arc that joins a line or circle smoothly, with no kink at the meeting point — the direction of the arc and the line match exactly there. You need it for rounded corners, the ends of curved arms, and smooth curve-to-line joins on laser-cut parts. This guide shows how to make one with the fillet command, gives the formula for where the tangent points land, and shows how to check the arc is really tangent.

What "tangent" means

Two lines that meet at a corner leave a kink. Slip in an arc that touches both lines and the join becomes smooth, because at the touch point the tangent of the circle runs parallel to the line. The key fact is that the arc's radius is always perpendicular to the line at the tangent point.

R R T1 T2 V arc centre sits R away, perpendicular from both lines
V = the original corner · T1, T2 = tangent points on each line · radius R is perpendicular to the line at each tangent point · the arc centre lies on the angle bisector

Method 1: fillet two lines

The fillet command builds a tangent arc between two lines automatically — the quickest and most accurate way.

  1. Draw two lines meeting at, or aimed into, a corner (press L).
  2. Run fillet and enter the radius R you want.
  3. Click the first line then the second. The program trims the overshoot and drops in a tangent arc that fits exactly.
If no arc appears after you enter R: the radius is too big to fit the length of the lines. Use a smaller radius, or extend the lines first so there is room.

Formula: where the tangent points land

To place the tangent points yourself, or to check the fillet is right, use these, where θ is the angle between the two lines at the corner.

To findFormula
Tangent length (corner → tangent point)t = R ÷ tan(θ ÷ 2)
Centre distance (corner → arc centre)d = R ÷ sin(θ ÷ 2)
Angle the arc sweepsα = 180° − θ
Arc lengthL = R × α (in radians)

Example A — right angle: two lines meeting at θ = 90°, fillet R = 10 mm.

  • Tangent points sit t = 10 ÷ tan 45° = 10 ÷ 1 = 10 mm from the corner, each side.
  • The arc sweeps α = 180° − 90° = 90° (exactly a quarter circle).
  • Arc length L = 10 × (90 × π ÷ 180) = 10 × 1.5708 = 15.71 mm

Example B — obtuse angle: two lines at θ = 120°, fillet R = 20 mm.

  • Tangent points sit t = 20 ÷ tan 60° = 20 ÷ 1.7320 = 11.55 mm from the corner.
  • The arc sweeps α = 180° − 120° = 60°.
  • Arc length L = 20 × (60 × π ÷ 180) = 20 × 1.0472 = 20.94 mm

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Method 2: tangent arc to a line and a circle, or two circles

The fillet command works on circles and arcs too, not only straight lines.

  1. Draw the line and circle (or two circles) you want the arc to touch.
  2. Run fillet, enter radius R, then click both objects on the side where you want the arc to appear — the side you click decides whether the arc falls inside or outside.
  3. If it comes out on the wrong side, press Ctrl+Z and click nearer the opposite side.
Tip: for an arc tangent to a circle from outside, the arc centre sits R + the circle radius from the circle centre; tangent from inside, it sits |circle radius − R|. If fillet can't find a solution, the radius you chose is geometrically impossible.

Check it's really tangent, not just close

  1. Zoom into the join. A visible corner means it is not tangent.
  2. Press M (measure) and check the distance from the arc centre to the tangent point equals the radius R and is perpendicular to the line.
  3. Before exporting for cutting, use trim to clear any line that overshoots the tangent point, so the path reads as one continuous outline.

Frequently asked questions

What is a tangent arc

An arc that joins a line or circle smoothly with no kink, because the arc and the line run in the same direction at the touch point. The arc's radius is always perpendicular to the line there.

How do I draw a tangent arc between two lines

Use the fillet command: enter the radius you want, then click the first line and the second. The program trims the corner and drops in a tangent arc that fits exactly.

Why won't fillet add an arc

Usually the radius is too large to fit the length of the lines — use a smaller one or extend the lines first. With circles it can mean the chosen radius is geometrically impossible.

How far from the corner is the tangent point

t = R ÷ tan(θ ÷ 2), where θ is the angle between the two lines. For a right angle with R = 10 mm the tangent points sit 10 mm from the corner on each side.

Summary

A tangent arc makes a join smooth with no kink. The easy way is the fillet command: enter a radius and click two objects. To place or check it yourself, use the tangent length t = R ÷ tan(θ/2) and the swept angle α = 180° − θ. Zoom in to confirm there is no kink, and use measure to verify the radius is perpendicular to the line at the tangent point before you export for cutting.