Home / Articles / Belt length between two pulleys (formula)
How to calculate · Production

Belt length between two pulleys (formula)

7 min read · updated 12 Nov 2026

When designing a belt drive the first thing you need is how long the belt must be to wrap both pulleys. You get it from the centre distance (C) and the large and small pulley diameters (D and d) with a single formula. This guide gives the belt-length shortcut, the wrap-angle formula, and the reverse formula for finding centre distance from a standard belt — all with worked examples that have been checked twice.

The values you need first

An open belt wraps two pulleys turning the same way. Its length comes from three parts: the two straight spans touching the pulleys, plus the arc that wraps each pulley. There are three main variables.

C D d large pulley Ø D small pulley Ø d
C = centre distance · D = large pulley diameter · d = small pulley diameter (for V-belts use the pitch diameter, not the outside edge)
SymbolMeaning
CCentre distance between the two shafts
DLarge pulley diameter
dSmall pulley diameter
LBelt length (the loop that fits both pulleys)

The belt-length formula

The formula used in practice is an approximation that is extremely accurate for real drives (within about 0.01% of the exact value when the pulleys are not wildly different in size).

Open-belt length:
L ≈ 2C + (π ÷ 2)(D + d) + (D − d)² ÷ (4C)
Keep every value in the same unit (all millimetres, say) and L comes out in that unit.

Each part is easy to read: 2C is the two straight spans, (π÷2)(D+d) is half the circumference of both pulleys combined, and the last term is a small correction that grows when the two pulleys differ a lot in size.

Example 1: pulleys D = 200 mm, d = 100 mm, centre distance C = 500 mm

L ≈ 2(500) + (π÷2)(200+100) + (200−100)² ÷ (4×500)
= 1000 + 1.5708 × 300 + 10000 ÷ 2000
= 1000 + 471.2 + 5.0 = 1476.2 mm

Wrap angle on the small pulley

The small pulley is where the belt wraps least, so it sets the grip and the slip. Its angle of wrap is

Small-pulley wrap angle: θ = 180° − 2 × arcsin[(D − d) ÷ 2C]

From Example 1: θ = 180° − 2 × arcsin(100 ÷ 1000) = 180° − 2(5.74°) = 168.5°. More wrap means more grip; if the wrap drops below 120°, increase the centre distance or add an idler pulley.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Centre distance from a standard belt

In practice it is often the other way round: you have bought a standard belt of length L and need to know what centre distance tensions it correctly. Rearranging the formula above gives

Centre distance from L: let B = 2L − π(D + d), then
C = [ B + √(B² − 8(D − d)²) ] ÷ 8

Example: belt L = 1476 mm, D = 200, d = 100
B = 2(1476) − π(300) = 2952 − 942.5 = 2009.5
C = [2009.5 + √(2009.5² − 8×100²)] ÷ 8 = [2009.5 + 1990.5] ÷ 8 = 500 mm (back to the original)

In practice set the shafts slightly closer than this so the belt slips on, then move the motor out to tension it — so design the motor base to adjust by about ±3% of C.

Check it by drawing in DXCAD2D

Before machining a base or drilling motor-mount holes, draw it to check.

  1. Press C and draw both pulley circles at their real diameters, placing the centres C apart (type coordinates such as 0,0 and 500,0).
  2. Press M to measure centre-to-centre and confirm C, and to measure the straight span so the motor clears the frame.
  3. Use L to draw the upper and lower tangent lines as the belt run — you will see the wrap angle and the space to leave for a guard.

Frequently asked questions

What is the belt length formula

For an open belt use L ≈ 2C + (π÷2)(D+d) + (D−d)²÷(4C), where C is the centre distance and D and d are the large and small pulley diameters, all in the same unit.

Which diameter do I use for a V-belt

Use the groove pitch (datum) diameter, not the outside edge of the pulley, because the belt's neutral line runs at the pitch level.

How do I find centre distance from belt length

Let B = 2L − π(D+d), then C = [B + √(B² − 8(D−d)²)] ÷ 8. Set the shafts slightly closer and move the motor out to tension the belt.

What happens if the wrap angle is too small

The belt grips less, slips and overheats. Keep the small-pulley wrap above about 120° by increasing the centre distance or adding an idler pulley.

Summary

Belt length between two pulleys comes from one formula: L ≈ 2C + (π÷2)(D+d) + (D−d)²÷4C. The small-pulley wrap angle is 180° − 2·arcsin[(D−d)÷2C], and if you already have a belt size you can back-calculate the centre distance with C = [B + √(B²−8(D−d)²)]÷8. Always use the pitch diameter for V-belts, then draw it in DXCAD2D to check before you build.