Home / Articles / Draw and calculate a worm gear: ratio, lead angle, centre distance
Draw + calculate

Draw and calculate a worm gear: ratio, lead angle, centre distance

8 min read · updated 18 Nov 2026

A worm gear (worm and worm wheel) gives a very high reduction in little space, and many pairs are also self-locking, so they suit hoists, roller-shutter drives and dividing heads. The calculation hinges on the module together with the number of worm starts and the wheel tooth count. This guide gives the formulas for ratio, lead angle, diameters and centre distance, with a worked 40:1 example and the steps to draw the pair in DXCAD2D Online.

Key dimensions of a worm gear

Let z₁ = number of worm starts, z₂ = number of wheel teeth, m = axial module (the worm's axial module equals the wheel's module), and q = the worm diameter factor.

DimensionFormula
Gear ratio iz₂ ÷ z₁
Axial pitch pxπ × m
Worm lead pzz₁ × π × m
Worm pitch dia d₁q × m
Lead angle γarctan( z₁ ÷ q )
Wheel pitch dia d₂z₂ × m
Centre distance a(d₁ + d₂) ÷ 2
Worm outside dia da1d₁ + 2m
Wheel throat dia da2d₂ + 2m
Root dia dfd − 2.4m (worm and wheel)
High ratio in little space: a spur pair steps down only a few times per stage, but a worm gear reduces by the wheel teeth divided by the worm starts — a 40-tooth wheel with a single-start worm gives 40:1 in one pair.
centre dist a worm worm wheel, pitch dia d₂
Meshing pair: the worm is a thread of axial pitch px driving the wheel at pitch dia d₂; the distance between the two shaft axes is a.

Worked example: a 40:1 ratio

Single-start worm z₁ = 1, wheel z₂ = 40 teeth, module m = 2 mm, diameter factor q = 10.

DimensionSubstituteResult
Gear ratio i40 ÷ 140 : 1
Axial pitch pxπ × 26.283 mm
Lead pz1 × π × 26.283 mm
Worm pitch dia d₁10 × 220.0 mm
Lead angle γarctan(1 ÷ 10)5.71°
Wheel pitch dia d₂40 × 280.0 mm
Centre distance a(20 + 80) ÷ 250.0 mm
Worm outside dia da120 + 2×224.0 mm
Wheel throat dia da280 + 2×284.0 mm

A 5.71° lead angle is low. Worm gears with a low lead angle (roughly < 5–6°) tend to be self-locking — the wheel cannot back-drive the worm — which suits hoists that must hold a load, at the cost of lower transmission efficiency than a spur gear.

Root diameters: with 0.2m clearance the root dia = d − 2.4m, so the worm df1 = 20 − 4.8 = 15.2 mm and the wheel df2 = 80 − 4.8 = 75.2 mm.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Drawing the pair in DXCAD2D

Draw it as a 2D meshing view: the wheel as a circle, the worm as a side-view thread, to the 40:1 numbers.

  1. Draw the wheel pitch circle with C (circle) at centre 0,0, radius 40 (d₂ = 80), and the outside circle radius 42 (da2 = 84).
  2. Locate the worm axis at centre distance a = 50 by drawing a guide line with L from 0,0 to -50,0; the end is the worm axis.
  3. Draw the worm pitch circle with C at the axis end, radius 10 (d₁ = 20) — it touches the wheel pitch circle exactly, since 40 + 10 = 50 = a.
  4. Draw the worm side view with REC (rect) as a bar along the axis, then the thread lines with L leaning at the 5.71° lead angle, repeated every axial pitch px = 6.283 with AR (array).
  5. Check the centre distance and diameters with ME (measure) before dimensioning.
  6. Dimension the centre distance a, wheel Ø and worm Ø with DLI (dimension linear).

For a full set of wheel teeth, draft one tooth and PO (polar array) it around the wheel centre 40 times, equal to z₂.

Frequently asked questions

how to calculate worm gear ratio

Ratio = wheel teeth ÷ worm starts. A 40-tooth wheel with a single-start worm gives 40:1; a two-start worm on the same wheel gives 20:1.

how to find worm gear lead angle

Lead angle γ = arctan(worm starts ÷ diameter factor q). For z₁ = 1 and q = 10 that is arctan(1÷10) = 5.71°.

when is a worm gear self-locking

Usually when the lead angle is low, roughly below 5–6° — the wheel cannot back-drive the worm. That suits hoists that must hold a load, but it lowers transmission efficiency.

how to calculate worm gear centre distance

Centre distance a = (worm pitch dia + wheel pitch dia) ÷ 2. For d₁ = 20 and d₂ = 80 that gives a = 50 mm.

Summary

A worm gear is calculated from the module m, worm starts z₁ and wheel teeth z₂: ratio = z₂ ÷ z₁, wheel pitch dia = z₂ × m, worm pitch dia = q × m, lead angle = arctan(z₁ ÷ q), centre distance = (d₁ + d₂) ÷ 2. The 40:1 example gives d₁ = 20, d₂ = 80, a = 50 mm and a 5.71° lead angle. Draw two pitch circles touching at distance a, dimension with DLI, and verify every value with ME before manufacture.