Home / Articles / Calculate and draw V-belt pulley grooves A B C
Draw + calculate · Production

Calculate and draw V-belt pulley grooves A B C

8 min read · updated 15 Nov 2026

A V-belt pulley is not sized from its rim — it is referenced to the pitch (datum) line, the position where the belt actually seats. V-belt grooves for sections A, B and C have fixed dimensions under ISO 4183, so once you know the belt section and the pitch diameter you want, you can work out the outside diameter, groove depth, groove angle and face width, then draw the groove section in DXCAD2D Online ready for the turner. This guide gives the formulas, the real groove-dimension table, a worked 2-groove example and the drawing steps.

The parts of a V-pulley groove

A V-groove is a symmetric V — wide at the rim, narrow at the bottom — with four key values: wd the groove width at the pitch line, b the distance from the pitch line up to the top face, h the depth from the pitch line down to the groove bottom, and the groove angle α.

pitch (datum) line wd b h α pulley top face (outside Ø)
Groove section: wd is the width at the pitch line · b is measured up to the top face · h down to the groove bottom · α is the groove angle.

ISO 4183 standard groove dimensions (classical belts)

For classical V-belts A (13×8 mm), B (17×11 mm) and C (22×14 mm), the pulley grooves have these dimensions (millimetres).

Sectionwd (width at pitch)b (pitch → top)h (pitch → bottom, min)e (groove spacing)f (rim → first groove, min)
A11.02.758.715.09.0
B14.03.510.819.011.5
C19.04.814.325.516.0
Important: the diameter used for ratio and belt speed is the pitch (datum) diameter, not the outside diameter. The relationship is outside Ø = pitch Ø + 2b.

Groove angle: 34° or 38°?

A V-belt has a section angle of about 40°, but as it bends around a pulley its inner material is compressed and bulges, so the effective wedge angle narrows. The smaller the pulley, the tighter the bend and the narrower the angle — so the groove is cut to a smaller angle to match.

ISO 4183 allows 32° / 34° / 36° / 38° (±0.5°). The rule of thumb is small pitch diameters use the smaller angle (34°), large pitch diameters use the larger angle (38°), with 36° as the middle band. The exact change-over diameter depends on the belt section, so check the standard's table or the maker's groove gauge before cutting.

Worked example: a 2-groove A pulley, pitch Ø 112 mm

Design a 2-groove A-section pulley with pitch diameter dd = 112 mm, running at 1450 rpm.

FindFormulaSubstituteResult
Outside Ødo = dd + 2b112 + 2(2.75)117.5 mm
Total groove depthb + h2.75 + 8.711.45 mm
Groove width at rimwd + 2b·tan(α/2)11 + 2(2.75)tan17°12.68 mm
Pulley face widthB = e(n−1) + 2f15(2−1) + 2(9)33 mm
Belt speedv = π·dd·N ÷ 60000π·112·1450 ÷ 600008.50 m/s

Use a 34° groove because the pitch diameter is still small; the half-angle α/2 = 17° (tan 17° ≈ 0.3057). The second groove sits exactly e = 15 mm from the first.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Drawing the groove section in DXCAD2D Online

Draw it as a half section (measured up from the shaft centreline) — it is the quickest way to get dimensions straight from the calculation.

  1. Press L to lay a horizontal shaft centreline, then offset it up by the pitch radius = 112 ÷ 2 = 56 mm to make the pitch line.
  2. Offset the pitch line up another 2.75 mm (the b value) to get the top face, at radius 58.75 (outside Ø 117.5).
  3. Press P and draw the groove section as a polyline by coordinates: the bottom is wd − 2h·tan17° = 11 − 2(8.7)(0.3057) = 5.68 mm wide, the rim is 12.68 mm wide, walls at 17° from vertical.
  4. Press M to check the depth b+h = 11.45 mm and the rim width 12.68 mm.
  5. Make the second groove with array or mirror at e = 15 mm spacing, then use D to dimension the outside Ø, pitch Ø, groove angle and the 33 mm face width.
Tip: the turner works from the pitch line and the groove angle, so put the pitch Ø, outside Ø, groove angle (°), depth and the e spacing on the drawing and the groove can be cut without guessing.

Frequently asked questions

Where is a V-belt pulley diameter measured

At the pitch (datum) diameter where the belt seats, not the outside diameter. The relationship is outside Ø = pitch Ø + 2b, so an A groove with b = 2.75 gives outside Ø = pitch Ø + 5.5 mm.

What is the groove angle of a V-belt pulley

Per ISO 4183 it is 32–38°, typically 34° for small pulleys and 38° for large ones, because the belt bends more tightly around a small pulley and its effective wedge angle narrows.

How deep is an A B or C V-belt groove

Total depth from the top face to the groove bottom = b + h, so A ≈ 11.45 mm, B ≈ 14.3 mm, C ≈ 19.1 mm (minimum values to ISO 4183).

How wide is a multi-groove pulley

Use B = e(n−1) + 2f where n is the number of grooves, e.g. a 3-groove A pulley = 15(3−1) + 2(9) = 48 mm (e and f come from the section table).

Can A and B belts use the same pulley groove

No. An A groove is 11 mm wide at the pitch line and a B groove is 14 mm — different widths and depths — so you must use a pulley made for the belt section.

Summary

V-pulley grooves are referenced to the pitch line. Remember three relationships: outside Ø = pitch Ø + 2b, groove depth = b + h, and multi-groove face width B = e(n−1) + 2f. Take the A/B/C groove values from the ISO 4183 table, pick a 34° angle for small pulleys and 38° for large ones, then draw the half section in DXCAD2D Online with offset, polyline and array and dimension it with dim — ready for the shop.