Home / Articles / Draw & calculate a 90° V-groove + ball/roller check
Draw + calculate · 2D

Draw & calculate a 90° V-groove + ball/roller check

7 min read · updated 16 Nov 2026

V-grooves and V-blocks with a 90° included angle are workshop staples — they cradle a round shaft dead-centre every time. This guide covers two things you actually use: drawing a 90° V-groove (how depth relates to opening width) and calculating how high a ball or shaft sits above the groove bottom with a gauge ball, which lets you check the groove's depth and symmetry without measuring the sharp corner directly.

Geometry of a 90° V-groove

A 90° included angle means the two faces are 90° apart, so each face leans 45° from vertical (and 45° from horizontal). That gives a relationship that is very easy to remember.

Golden rule (90° vee only): groove depth = half the opening width, because at 45° every bit deeper narrows the groove by the same amount per side. Opening 40 → depth 20.

If the included angle is not 90° (say 60° or 120°), use the general form: depth = (opening width ÷ 2) ÷ tan(included angle ÷ 2).

Calculate how high a ball/shaft sits above the bottom

Drop a ball or round shaft of diameter d into a 90° vee and it touches both faces, sitting a fixed height above the sharp apex (the theoretical bottom). The formula comes from the radius r = d/2.

r√2 r(1+√2) 90° centre
Ball d in a 90° vee: the centre sits r√2 above the apex, and the top of the ball sits r(1+√2) = 1.2071 × d above the apex.
To findFormula (90° vee)Approx.
Ball centre above apexr ÷ sin45° = r√20.7071 × d
Top of ball above apexr(1 + √2)1.2071 × d

Worked example — a Ø20 gauge ball in a 90° vee:

  1. Radius r = d ÷ 2 = 20 ÷ 2 = 10 mm
  2. Centre above apex = r√2 = 10 × 1.4142 = 14.142 mm
  3. Top of ball above apex = r(1 + √2) = 10 × 2.4142 = 24.142 mm

Measure from the bottom (or from a top edge whose height you know) up to the top of the ball. Read 24.14 and the vee is 90° and symmetric; if the ball leans to one side, the two faces aren't equal. A Ø25 shaft in the same vee sits at 12.5 × 2.4142 = 30.18 mm above the apex.

Why measure with a ball: a real groove bottom is usually broken or relieved, so measuring the sharp corner is unreliable. A ball only touches the two sloped faces, so it reflects the angle and symmetry far better.

Draw a 90° V-groove in the program

Draw a V-block section with opening W = 40 and depth 20 (= W/2), with the groove apex at (0,0).

  1. Type R (rect) for the block, e.g. lower-left -30,0 to upper-right #30,25 (the apex falls inside).
  2. Type P (polyline) for the two vee faces: start at the left lip -20,20 Enter → apex #0,0 Enter → right lip #20,20 Enter (at 45° the lip is 20 per side = the depth 20).
  3. Type trim and cut the block's top edge between the two lips, leaving an open vee.
  4. Add sizes: type D (dim) for the 40 opening and the 20 depth, and note the 90° at the apex.

For another angle, say 60°, move the apex: lip half-width a and depth h relate by a = h × tan(included ÷ 2).

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Top-of-ball above apex table (90° vee)

Ball/shaft Ø (mm)Centre above apex 0.7071×dTop above apex 1.2071×d
107.0712.07
128.4914.49
1611.3119.31
2014.1424.14
2517.6830.18

Frequently asked questions

How deep is a 90 degree V-groove

The depth is always half the opening width, because the faces lean 45°. Opening 40 is 20 deep, opening 50 is 25 deep.

How high does a ball sit in a 90 degree vee

The top of the ball sits 1.2071 × its diameter above the sharp apex, and the centre sits 0.7071 × diameter. A Ø20 ball tops out 24.14 mm above the bottom.

How do I check a V-groove angle accurately

Drop a gauge ball in and measure from the bottom or a known top edge to the top of the ball, then compare with 1.2071 × d. Matching means 90°; a ball that doesn't lean means the two faces are equal.

How do I calculate a vee that isn't 90 degrees

Depth = (opening width ÷ 2) ÷ tan(included angle ÷ 2), and top of ball above apex = r(1 + 1 ÷ sin(included angle ÷ 2)).

Summary

For a 90° vee, remember two things: depth = half the opening width (faces at 45°), and a ball or shaft tops out 1.2071 × its diameter above the apex. To draw it, put the apex at (0,0) and run each face up by the depth per side. To check a part, drop in a gauge ball and measure to its top against the formula — you learn both the angle and the symmetry without ever touching the sharp corner.