Draw & calculate a 90° V-groove + ball/roller check
V-grooves and V-blocks with a 90° included angle are workshop staples — they cradle a round shaft dead-centre every time. This guide covers two things you actually use: drawing a 90° V-groove (how depth relates to opening width) and calculating how high a ball or shaft sits above the groove bottom with a gauge ball, which lets you check the groove's depth and symmetry without measuring the sharp corner directly.
Geometry of a 90° V-groove
A 90° included angle means the two faces are 90° apart, so each face leans 45° from vertical (and 45° from horizontal). That gives a relationship that is very easy to remember.
If the included angle is not 90° (say 60° or 120°), use the general form: depth = (opening width ÷ 2) ÷ tan(included angle ÷ 2).
Calculate how high a ball/shaft sits above the bottom
Drop a ball or round shaft of diameter d into a 90° vee and it touches both faces, sitting a fixed height above the sharp apex (the theoretical bottom). The formula comes from the radius r = d/2.
| To find | Formula (90° vee) | Approx. |
|---|---|---|
| Ball centre above apex | r ÷ sin45° = r√2 | 0.7071 × d |
| Top of ball above apex | r(1 + √2) | 1.2071 × d |
Worked example — a Ø20 gauge ball in a 90° vee:
- Radius r = d ÷ 2 = 20 ÷ 2 = 10 mm
- Centre above apex = r√2 = 10 × 1.4142 = 14.142 mm
- Top of ball above apex = r(1 + √2) = 10 × 2.4142 = 24.142 mm
Measure from the bottom (or from a top edge whose height you know) up to the top of the ball. Read 24.14 and the vee is 90° and symmetric; if the ball leans to one side, the two faces aren't equal. A Ø25 shaft in the same vee sits at 12.5 × 2.4142 = 30.18 mm above the apex.
Draw a 90° V-groove in the program
Draw a V-block section with opening W = 40 and depth 20 (= W/2), with the groove apex at (0,0).
- Type R (rect) for the block, e.g. lower-left
-30,0to upper-right#30,25(the apex falls inside). - Type P (polyline) for the two vee faces: start at the left lip
-20,20Enter → apex#0,0Enter → right lip#20,20Enter (at 45° the lip is 20 per side = the depth 20). - Type trim and cut the block's top edge between the two lips, leaving an open vee.
- Add sizes: type D (dim) for the 40 opening and the 20 depth, and note the 90° at the apex.
For another angle, say 60°, move the apex: lip half-width a and depth h relate by a = h × tan(included ÷ 2).
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineTop-of-ball above apex table (90° vee)
| Ball/shaft Ø (mm) | Centre above apex 0.7071×d | Top above apex 1.2071×d |
|---|---|---|
| 10 | 7.07 | 12.07 |
| 12 | 8.49 | 14.49 |
| 16 | 11.31 | 19.31 |
| 20 | 14.14 | 24.14 |
| 25 | 17.68 | 30.18 |
Frequently asked questions
How deep is a 90 degree V-groove
The depth is always half the opening width, because the faces lean 45°. Opening 40 is 20 deep, opening 50 is 25 deep.
How high does a ball sit in a 90 degree vee
The top of the ball sits 1.2071 × its diameter above the sharp apex, and the centre sits 0.7071 × diameter. A Ø20 ball tops out 24.14 mm above the bottom.
How do I check a V-groove angle accurately
Drop a gauge ball in and measure from the bottom or a known top edge to the top of the ball, then compare with 1.2071 × d. Matching means 90°; a ball that doesn't lean means the two faces are equal.
How do I calculate a vee that isn't 90 degrees
Depth = (opening width ÷ 2) ÷ tan(included angle ÷ 2), and top of ball above apex = r(1 + 1 ÷ sin(included angle ÷ 2)).
Summary
For a 90° vee, remember two things: depth = half the opening width (faces at 45°), and a ball or shaft tops out 1.2071 × its diameter above the apex. To draw it, put the apex at (0,0) and run each face up by the depth per side. To check a part, drop in a gauge ball and measure to its top against the formula — you learn both the angle and the symmetry without ever touching the sharp corner.