Home / Articles / How to draw a slot (obround hole) to exact size
How to draw · Basics

How to draw a slot (obround hole) to exact size

6 min read · updated 7 Nov 2026

A slot, or obround hole, has two semicircular ends joined by two parallel straight lines. It is used wherever a screw needs room to adjust or a cable needs to pass. The key to drawing it to size is that the end radius equals half the width, and the distance between the two end centres equals length − width. This guide shows two ways to draw it in DXCAD2D Online — one easy, one exact.

The geometry of a slot

A slot has three main values with fixed relationships. Set the overall length L (measured end to end) and the width W, and the rest follow at once.

To findFormulaExample L 40 · W 12
End radius RR = W ÷ 26 mm
Centre distance CC = L − W28 mm
Overall length L (check)L = C + W = C + 2R28 + 12 = 40 mm
length L centres C = L − W W R
A slot: the ends are semicircles of radius R = W/2, and the two end centres are C = L − W apart.

Method 1: rectangle + fillet (easiest)

This is quick and needs little coordinate work. It relies on the fact that when you fillet with a radius equal to half the width, the four corners merge into exact semicircles.

  1. Press REC and draw a rectangle of length L × width W, e.g. type the size 40,12.
  2. Use fillet, set the radius to R = W ÷ 2 (here 6), and fillet all four corners.
  3. Because the fillet radius equals half the width, both ends become full semicircles — an exact slot.
rectangle L × W (dashed) fillet R = W/2 on all 4 corners → slot
Draw a rectangle L × W, then fillet all four corners with a radius of half the width to get a slot straight away.

Method 2: two circles + tangent lines (most accurate)

If you want exact placement by coordinates, put the left end centre at (0,0) and the right end centre at (C,0), where C = L − W.

  1. Press C and draw two circles of radius R = W/2 at (0,0) and (C,0) — e.g. radius 6 at 0,0 and 28,0.
  2. Press L and draw the top and bottom tangent lines: top from (0, R) to (C, R) and bottom from (0, −R) to (C, −R) — e.g. 0,6 to 28,6.
  3. Use trim to cut away the inner halves of the circles, leaving only the two end semicircles.

Example: a slot 40 long and 12 wide → R = 6, C = 28. Two circles at (0,0) and (28,0); top line (0,6)–(28,6), bottom line (0,−6)–(28,−6). Check: overall length = 28 + 2×6 = 40 ✓

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Dimensioning and tips for the cutter

On a drawing a slot is usually called out as length × width followed by the slot symbol, or written as "2× R6" to state the end radius.

  • Press D and dimension both the overall length L and the width W, so the cutter never has to guess.
  • Give the coordinate of the slot centre (the midpoint between the two ends) to locate it on the part.
  • For several identical slots, draw one and use array or mirror to repeat it — every copy is then the same size.
  • Before exporting the DXF, check the outline is fully closed (try hatch: if it fills, the shape is closed). A laser cutter needs a closed loop to cut the hole.

Frequently asked questions

What is an obround slot

It is a long hole with two semicircular ends joined by two parallel straight lines. Unlike an ellipse, the ends are true circular arcs. It is commonly used as an adjustment slot for screws.

What is the end radius of a slot

Always half the width: R = W ÷ 2. A slot 12 mm wide has 6 mm radius ends.

How do I draw a slot in CAD the easy way

Draw a rectangle of length × width, then fillet all four corners with a radius equal to half the width. The corners merge into semicircles and the rectangle becomes a slot.

How do I find the centre distance of a slot

The distance between the two end centres equals overall length minus width (C = L − W). A slot 40 long and 12 wide has centres 28 mm apart.

Summary

A slot is two semicircles joined by straight lines. Remember just two values: end radius R = W/2 and centre distance C = L − W. The easiest way is to draw a rectangle L × W and fillet all four corners at half the width; the exact way is to place two circles at coordinates and join them with tangent lines. Always dimension it and check the outline is closed before exporting a cutting file.