Home / Articles / How to draw centerlines correctly
How to draw · 2D drafting

How to draw centerlines correctly

6 min read · updated 11 Nov 2026

A centerline (center line) is a thin line made of alternating long and short dashes that marks the axis of symmetry of a part and the center of a hole or circle. Draw them correctly and the drawing reads clearly, hole positions are obvious, and dimensions sit cleanly. This guide explains the line pattern, the rules that matter, and how to draw centerlines in DXCAD2D Online.

What a centerline looks like

A centerline is a thin line drawn as a chain, alternating a long segment with a short one. Two standards are common:

  • ISO 128 style: long dash then dot (a long dash followed by a small dot in the gap).
  • ASME style: long–short–long dashes repeating.

Both are thin lines and mean the same thing. The exact proportions depend on the drawing size: typically the long segment is about 10–30 mm, the short dash or dot about 1.5–3 mm, and the gaps about 1–2 mm. Keep it consistent across the whole sheet.

Cross at a long dash, exactly at the center Ends extend a little past the circle (~2–3 mm) Start and end on a long dash
Two perpendicular centerlines for a circle cross at a long dash right at the center and extend slightly past the outline.

The rules that matter

  1. Cross at a long dash. The center of a hole must be where two long dashes cross (a + cross), not where two gaps meet.
  2. Extend slightly past the feature. The ends should reach about 2–3 mm beyond the outline or circle — enough to be clear, not so long it clutters.
  3. Start and end with a long dash. Never let a line end on a dot or a gap.
  4. Small holes. If a hole is too small to fit the dash pattern, use a short thin cross instead.
  5. Thinner than the outline. A centerline must be clearly thinner than the object line so it is not mistaken for a real edge.

Bolt-circle (PCD) centerlines

For a ring of holes (a bolt circle / PCD), draw the centerline as a single chain circle through the centers of all the holes, then add a short radial centerline cross at each hole. This shows both the pitch-circle diameter and every hole position in one picture.

Tip: for holes on a PCD, work out each hole's X, Y coordinate first, then place the centerline crosses. See the bolt-hole coordinates article for the calculation.
chain circle = PCD centerline short cross at each hole
The bolt-circle centerline is a chain circle through every hole center, with a short centerline cross at each hole.

Draw centerlines in DXCAD2D Online

  1. Use L (line) through the center and set it to a thin center/chain style — see the line types and weights article for choosing the style and weight.
  2. Extend it about 2–3 mm past the outline and make sure the crossing lands on a long dash right at the center of the hole.
  3. For a symmetric part, place the centerline on the axis of symmetry first, draw one half, then use mirror to produce the other half exactly.
  4. For a bolt circle of equally spaced holes, place the first hole and use array to repeat it around the center, centerline cross and all.

Frequently asked questions

What line type is a centerline

A thin chain line of alternating long and short segments. The ISO style is long-dash-dot; the ASME style is long-short-long. Both must be thinner than the object outline.

Should centerlines extend past the outline

Yes — they should reach about 2–3 mm beyond the edge or circle, but not so far that they clutter the view.

Where should centerlines cross

Exactly at the center of the hole or circle, and the crossing must be where two long dashes meet, not where two gaps meet.

How do you draw a centerline for a very small hole

If the hole is too small for the dash pattern to read, use a short thin cross instead of the full chain line.

Is a centerline the same as a symmetry line

They use the same line style. A centerline marks the center of a hole or shaft; a symmetry line marks an axis where both halves are identical. Some standards add a short double-dash mark at the ends of a symmetry line.

Summary

A centerline is a thin chain line of alternating long and short dashes. The rules to remember: cross at a long dash at the center of the hole, extend about 2–3 mm past the outline, start and end on a long dash, and keep it thinner than the object line. A bolt circle is drawn as a chain circle through every hole with a short cross at each one. You can draw, mirror and array all of this directly in DXCAD2D Online.