Draw and calculate a pipe notch (fishmouth) from the OD
Welding one round tube onto another — handrails, steel frames, a branch off a main — means cutting the end of the branch tube into a fishmouth (saddle cut / pipe coping) so it sits flush against the curved surface of the run tube before welding. This guide gives the formula for the notch depth, how to build a rise table for a wrap-around template, and the steps to draw the fishmouth curve in DXCAD2D. It covers the most common case: a branch tube meeting the run tube at 90° with the axes intersecting.
Variables and the key formula
Let R = the outer radius of the run tube (the one being branched into) and r = the outer radius of the branch tube (the one you notch), with r ≤ R. When the branch meets the run at 90°, the two surfaces intersect in a curve. The notch depth (the distance from the shallowest to the deepest point of the cut) is
It is the difference between the sides of the branch (parallel to the run axis — cut deepest) and the centre of the notch (facing the run — cut shallowest).
If the two tubes are equal (r = R) the notch depth equals R exactly (as deep as the tube radius) — this is the classic 45° cut used when joining tubes of the same size.
A worked example with real numbers
Problem: join a Ø48 mm branch (r = 24) onto a Ø60 mm main (R = 30) at 90°. Find the notch depth and the template values.
Notch depth = R − √(R² − r²) = 30 − √(30² − 24²) = 30 − √(900 − 576) = 30 − √324 = 30 − 18 = 12 mm
Unrolled onto a flat template the fishmouth becomes a curve. The rise (height above the deepest cut line) at angle φ around the branch is
φ = 0° is the side of the tube (parallel to the run axis, cut deepest → rise 0) · φ = 90° faces the run (cut shallowest → rise equals the notch depth)
Divide the branch circumference into 24 parts (every 15°). The circumference = π × 48 = 150.8 mm, so stations are 6.28 mm apart. The rise over one quarter turn is below (the other three quarters are symmetrical).
| Station φ | Distance round (mm) | Rise (mm) |
|---|---|---|
| 0° | 0.00 | 0.00 |
| 15° | 6.28 | 0.65 |
| 30° | 12.57 | 2.51 |
| 45° | 18.85 | 5.26 |
| 60° | 25.13 | 8.37 |
| 75° | 31.42 | 10.96 |
| 90° | 37.70 | 12.00 |
Over a full 360° turn there are two deepest points (φ = 0° and 180°) and two shallowest points (φ = 90° and 270°); the rise waves up and down symmetrically over four quarters, each the same as the table.
Drawing the fishmouth curve (unrolled template) in DXCAD2D
The goal is to draw the fishmouth curve at 1:1, print it, wrap it round the tube and scribe the cut line.
- Type L and press Enter, draw a horizontal datum line as long as the circumference, 150.8 mm — this is the deepest-cut line where the rise is 0.
- Type PL and press Enter for a polyline, then enter each point as an absolute coordinate (prefix with
#), station by station:#0,0#6.28,0.65#12.57,2.51#18.85,5.26#25.13,8.37#31.42,10.96#37.70,12… - Continue round the full turn: from 90° to 180° the rise falls back symmetrically (10.96, 8.37, 5.26, 2.51, 0.65, 0 at 75.40 mm), then rises to its peak again at 270° and returns to 0 at the end of the wrap, 150.8 mm.
- Type D to dimension the 12 mm notch depth and the wrap length as a check before printing.
- Print at 1:1 (see print a drawing to scale), cut the paper along the curve, wrap it round the tube end with the datum line on the square-cut end, and scribe the fishmouth along the curved edge.
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineWatch out
The formula above is for a branch at 90° to the run with the axes intersecting. For an angled joint or an offset (eccentric) branch the fishmouth is no longer symmetrical and you must project each intersection point individually (the ordinate method, using a side view and an end view). For angled tube and frame joints, see miter angles for frames and tubes.
Frequently asked questions
how deep is a pipe fishmouth notch
For a branch tube at 90° to the run, the notch depth = R − √(R² − r²), where R is the run's outer radius and r is the branch's outer radius. A Ø48 branch into a Ø60 run gives a 12 mm notch.
how deep is a fishmouth on equal diameter tubes
If both tubes are the same diameter (r = R) the notch depth equals R — as deep as the tube radius — and the cut is a clean 45° joint.
is a fishmouth the same as a saddle cut
Yes. Fishmouth, saddle cut and pipe coping all mean cutting a tube end to follow the curved surface of another tube before welding.
how do I make a pipe notch template
Work out the rise every 15° round the tube (R − √(R² − r²·sin²φ)), draw the curve on a flat template as long as the branch circumference, print it 1:1, then wrap it round the tube end to scribe the cut.
Summary
A perpendicular pipe fishmouth comes from one formula: depth = R − √(R² − r²), and unrolled it is a rise of R − √(R² − r²·sin²φ) every 15° round the tube. In the example a Ø48 branch into a Ø60 main gives a 12 mm notch. Plot the curve from coordinates in DXCAD2D, print it 1:1, wrap it round the tube and scribe. Angled or offset branches need each point projected individually.