Home / Articles / Draw and calculate a straight bevel gear
Draw + calculate · Production

Draw and calculate a straight bevel gear

8 min read · updated 21 Nov 2026

A bevel gear transmits power between intersecting shafts, usually at 90°. Its teeth sit on a cone, not a cylinder, so the design adds two values you do not meet in spur gears: the pitch cone angle (δ) and the outer cone distance (Re). This guide gives the complete set of formulas for a straight bevel gear at a 90° shaft angle, a worked 20/40-tooth, module-3 example, and the steps to lay out the section in DXCAD2D.

The key values of a bevel gear

Start with module m and tooth count z, as for a spur gear: the pitch diameter d = m·z, measured at the large (outer) end of the tooth. What is new is the cone angle, because a mating bevel pair must share one common apex.

Formulas (shaft angle Σ = 90°, straight bevel):
Pitch dia: d = m·z
Pinion pitch cone angle: tan δ₁ = z₁ / z₂ · Gear: δ₂ = 90° − δ₁
Outer cone distance: Re = d / (2 · sin δ) (same value for both members)
Outside dia: dₐ = d + 2·m·cos δ = m(z + 2cos δ)
addendum = m · dedendum = 1.25·m · face width b ≈ Re/3 (and ≤ 10m)
axis δ Re d/2 apex pitch line at angle δ from the axis
Pitch-cone section: the pitch line runs from the apex at angle δ for length Re to the large end, whose pitch radius is d/2.

Worked example: a 20/40-tooth pair, module 3

Pinion z₁ = 20, gear z₂ = 40, module m = 3, shaft angle 90°.

1) Pitch diameter: d₁ = 3 × 20 = 60 mm · d₂ = 3 × 40 = 120 mm

2) Pitch cone angle: tan δ₁ = z₁/z₂ = 20/40 = 0.5 → δ₁ = 26.565° · δ₂ = 90 − 26.565 = 63.435° (check: tan δ₂ = 40/20 = 2 → 63.435° ✓)

3) Outer cone distance: Re = d₁ / (2·sin δ₁) = 60 / (2 × 0.4472) = 67.08 mm (from the gear it is the same: 120 / (2 × 0.8944) = 67.08 ✓)

4) Outside diameter (addendum = m = 3):
pinion dₐ₁ = 60 + 2×3×cos 26.565° = 60 + 6×0.8944 = 65.37 mm
gear dₐ₂ = 120 + 2×3×cos 63.435° = 120 + 6×0.4472 = 122.68 mm

5) Addendum / dedendum angles: θₐ = atan(m/Re) = atan(3/67.08) = 2.56° · θ_f = atan(1.25m/Re) = atan(3.75/67.08) = 3.20°
pinion face angle = δ₁ + θₐ = 29.13° · root angle = δ₁ − θ_f = 23.37°

6) Face width: b ≈ Re/3 = 67.08/3 = 22.4 → choose 20 mm (keep ≤ 10m = 30 mm)

Watch out: the outside diameter of a bevel gear is not d + 2m as for a spur gear — you must multiply by cos δ, because the addendum is added perpendicular to the cone line, not to the axis.

Summary of the example pair

ValuePinion (z=20)Gear (z=40)
Pitch dia d (mm)60120
Pitch cone angle δ26.565°63.435°
Outer cone distance Re (mm)67.0867.08
Outside dia dₐ (mm)65.37122.68
Face angle29.13°65.995°
Root angle23.37°60.235°

Lay out the bevel section in DXCAD2D

Drawing full bevel teeth in 2D is awkward, so lay out the "pitch-cone section" to check angles and sizes before cutting. Using the pinion:

  1. Press L and draw the horizontal axis through the apex at 0,0.
  2. Press L and draw the pitch line from 0,0 for Re = 67.08 at δ₁ = 26.565° — type the end point as the coordinate #60,30 (Re·cosδ = 60, Re·sinδ = 30, which matches the pitch radius d/2 = 30 exactly).
  3. Press L and draw the back-cone line from the end of the pitch line perpendicular down to the axis.
  4. Press offset and offset the pitch line up by m = 3 (tip) and down by 1.25m = 3.75 (root) to get the face and root cones.
  5. Press D and dimension δ₁, Re, pitch dia 60 and outside dia 65.37 · use M to re-check the angle and lengths.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Frequently asked questions

How do I calculate the cone angle of a bevel gear

At a 90° shaft angle use tan δ₁ = z₁/z₂ for the pinion. For a 20/40-tooth pair, tan δ₁ = 0.5 → δ₁ = 26.565°, and the gear is δ₂ = 90 − 26.565 = 63.435°.

How do I find the outside diameter of a bevel gear

Use dₐ = d + 2·m·cos δ, not d + 2m as for a spur gear, because the addendum is added perpendicular to the cone. For the pinion: 60 + 6×cos26.565° = 65.37 mm.

What is the outer cone distance Re

It is the length of the pitch line from the apex to the large end of the tooth, Re = d/(2 sin δ). It sets the face width b, which is usually kept to about Re/3 or less.

How is a bevel gear different from a spur gear

A spur gear drives parallel shafts with teeth on a cylinder; a bevel gear drives intersecting shafts (usually 90°) with teeth on a cone that taper toward the apex.

Summary

Designing a bevel gear starts like a spur gear (d = m·z), then adds the pitch cone angle tan δ₁ = z₁/z₂ and the outer cone distance Re = d/(2 sin δ). Remember that the outside diameter carries a cos δ term (dₐ = m(z + 2cos δ)) and that face width b ≈ Re/3. Lay out the pitch-cone section in DXCAD2D to verify the angles and sizes before you order the part.