Draw and calculate a straight bevel gear
A bevel gear transmits power between intersecting shafts, usually at 90°. Its teeth sit on a cone, not a cylinder, so the design adds two values you do not meet in spur gears: the pitch cone angle (δ) and the outer cone distance (Re). This guide gives the complete set of formulas for a straight bevel gear at a 90° shaft angle, a worked 20/40-tooth, module-3 example, and the steps to lay out the section in DXCAD2D.
The key values of a bevel gear
Start with module m and tooth count z, as for a spur gear: the pitch diameter d = m·z, measured at the large (outer) end of the tooth. What is new is the cone angle, because a mating bevel pair must share one common apex.
Pitch dia: d = m·z
Pinion pitch cone angle: tan δ₁ = z₁ / z₂ · Gear: δ₂ = 90° − δ₁
Outer cone distance: Re = d / (2 · sin δ) (same value for both members)
Outside dia: dₐ = d + 2·m·cos δ = m(z + 2cos δ)
addendum = m · dedendum = 1.25·m · face width b ≈ Re/3 (and ≤ 10m)
Worked example: a 20/40-tooth pair, module 3
Pinion z₁ = 20, gear z₂ = 40, module m = 3, shaft angle 90°.
1) Pitch diameter: d₁ = 3 × 20 = 60 mm · d₂ = 3 × 40 = 120 mm
2) Pitch cone angle: tan δ₁ = z₁/z₂ = 20/40 = 0.5 → δ₁ = 26.565° · δ₂ = 90 − 26.565 = 63.435° (check: tan δ₂ = 40/20 = 2 → 63.435° ✓)
3) Outer cone distance: Re = d₁ / (2·sin δ₁) = 60 / (2 × 0.4472) = 67.08 mm (from the gear it is the same: 120 / (2 × 0.8944) = 67.08 ✓)
4) Outside diameter (addendum = m = 3):
pinion dₐ₁ = 60 + 2×3×cos 26.565° = 60 + 6×0.8944 = 65.37 mm
gear dₐ₂ = 120 + 2×3×cos 63.435° = 120 + 6×0.4472 = 122.68 mm
5) Addendum / dedendum angles: θₐ = atan(m/Re) = atan(3/67.08) = 2.56° · θ_f = atan(1.25m/Re) = atan(3.75/67.08) = 3.20°
pinion face angle = δ₁ + θₐ = 29.13° · root angle = δ₁ − θ_f = 23.37°
6) Face width: b ≈ Re/3 = 67.08/3 = 22.4 → choose 20 mm (keep ≤ 10m = 30 mm)
Summary of the example pair
| Value | Pinion (z=20) | Gear (z=40) |
|---|---|---|
| Pitch dia d (mm) | 60 | 120 |
| Pitch cone angle δ | 26.565° | 63.435° |
| Outer cone distance Re (mm) | 67.08 | 67.08 |
| Outside dia dₐ (mm) | 65.37 | 122.68 |
| Face angle | 29.13° | 65.995° |
| Root angle | 23.37° | 60.235° |
Lay out the bevel section in DXCAD2D
Drawing full bevel teeth in 2D is awkward, so lay out the "pitch-cone section" to check angles and sizes before cutting. Using the pinion:
- Press L and draw the horizontal axis through the apex at
0,0. - Press L and draw the pitch line from
0,0for Re = 67.08 at δ₁ = 26.565° — type the end point as the coordinate#60,30(Re·cosδ = 60, Re·sinδ = 30, which matches the pitch radius d/2 = 30 exactly). - Press L and draw the back-cone line from the end of the pitch line perpendicular down to the axis.
- Press offset and offset the pitch line up by m = 3 (tip) and down by 1.25m = 3.75 (root) to get the face and root cones.
- Press D and dimension δ₁, Re, pitch dia 60 and outside dia 65.37 · use M to re-check the angle and lengths.
Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.
Open DXCAD2D OnlineFrequently asked questions
How do I calculate the cone angle of a bevel gear
At a 90° shaft angle use tan δ₁ = z₁/z₂ for the pinion. For a 20/40-tooth pair, tan δ₁ = 0.5 → δ₁ = 26.565°, and the gear is δ₂ = 90 − 26.565 = 63.435°.
How do I find the outside diameter of a bevel gear
Use dₐ = d + 2·m·cos δ, not d + 2m as for a spur gear, because the addendum is added perpendicular to the cone. For the pinion: 60 + 6×cos26.565° = 65.37 mm.
What is the outer cone distance Re
It is the length of the pitch line from the apex to the large end of the tooth, Re = d/(2 sin δ). It sets the face width b, which is usually kept to about Re/3 or less.
How is a bevel gear different from a spur gear
A spur gear drives parallel shafts with teeth on a cylinder; a bevel gear drives intersecting shafts (usually 90°) with teeth on a cone that taper toward the apex.
Summary
Designing a bevel gear starts like a spur gear (d = m·z), then adds the pitch cone angle tan δ₁ = z₁/z₂ and the outer cone distance Re = d/(2 sin δ). Remember that the outside diameter carries a cos δ term (dₐ = m(z + 2cos δ)) and that face width b ≈ Re/3. Lay out the pitch-cone section in DXCAD2D to verify the angles and sizes before you order the part.