Home / Articles / DXF file too big / too many points: how to reduce it
Troubleshooting · 2D drafting

DXF file too big / too many points: how to reduce it

7 min read · updated 8 Nov 2026

Sometimes you open a DXF and a simple curve turns out to have hundreds or thousands of nodes — the file is unusually large, and the laser, plasma or router reads it slowly, stutters, or won't accept it at all. Almost always the cause is the same: curves exploded into many short straight lines instead of true arcs. This guide explains the main causes and how to cut the point count so the file is small and the cutter runs smoothly.

Why too many points is a problem

The cutter's controller processes every point as one move command. When a single circle becomes dozens of short straight lines, the head has to stop-turn-go for each segment, which causes:

  • files several times larger that load and transfer slowly;
  • a stuttering head, dropped speed, and burn or dwell marks at every node;
  • faceted edges instead of smooth curves;
  • rejection by controllers that cap nodes per file or per entity.
true arc: 1 entity segments: dozens of points
The same curve: on the left a true arc uses one entity; on the right it is exploded into short straight lines, so it carries many points.

Cause 1: curves exploded into segments

This is the most common cause. Files exported from some programs, or converted from a PDF or image, often represent circles and arcs as strings of short straight lines (a polyline). The finer the setting, the more points.

To picture it: a Ø50 mm circle exploded into straight lines at a chord deviation of 0.1 mm becomes about 36 lines; tighten that to 0.05 mm and it rises to about 50 — when it should have been a single circle entity.

Fix: draw or export using true arcs and circles. In DXCAD2D use C for circles and fillet for rounded corners instead of stringing short lines together. When exporting from the source program, choose the option that keeps arcs (keep arcs / export as arcs) if it has one.

Cause 2: tolerance set finer than needed

When a curve genuinely has to be broken into segments (exporting a spline, say), the tolerance — the chord deviation — controls the point count. Set it too small and you get a huge number of points for no benefit.

ToleranceLines for a Ø50 circleSuitable for
0.1 mm~36general cutting, plenty
0.05 mm~50moderately fine work
0.02 mm~79very fine (far more points)

For general metal cutting, 0.05–0.1 mm is already finer than the eye can see — there is no need to go smaller. Tighter settings just add points without adding real quality.

Try it right now — a free 2D CAD in your browser. Nothing to install, no sign-up.

Open DXCAD2D Online

Cause 3: overlapping lines and broken-up edges

Lines drawn twice on top of each other, or an edge broken into many little pieces, inflate the entity and point count for nothing — and make the cutter re-cut the same path.

  • Remove duplicates: find lines that lie exactly on top of one another and delete the copies, leaving one.
  • Join into one path: merge lines and arcs that meet end-to-end into a single closed polyline (see the article on joining an open polyline).
  • Text: text converted to outlines becomes dozens of points per character. If it doesn't need cutting, keep it as text or delete it.

A systematic way to cut the points

  1. Open the file in DXCAD2D with open and find the curves that carry many points.
  2. Redraw the circles and arcs with C and fillet as true entities, then delete the old segment strings.
  3. Use offset and trim to tidy the lines, and close broken ends with PL (polyline).
  4. Delete overlapping lines and any text that doesn't need cutting.
  5. Check with M that key dimensions still match the original after editing.
  6. Export a new DXF and compare the file size — it is usually much smaller.
Watch out: don't reduce points until the shape distorts. The goal is to replace unnecessary segments with true arcs, not to drop real detail. Measure key sizes before and after to confirm the shape hasn't changed.

Frequently asked questions

Why does a DXF have too many points

Mainly because curves and circles are exploded into many short straight lines instead of true arcs — often from a PDF or image conversion, or an export tolerance set too small, plus overlapping lines and text converted to outlines.

How do I reduce DXF file size

Replace exploded curves with true circles and arcs, delete duplicate lines, join broken edges into single polylines, and remove text or detail that doesn't need cutting.

What tolerance should I use

For general metal cutting, 0.05–0.1 mm is fine enough. Smaller barely improves quality but adds a lot of points.

How many points should a circle have

Kept as a true circle it is a single entity with no node count. If it must be segmented, a Ø50 circle at 0.1 mm gives about 36 lines, which is plenty.

Can too many points stop the cutter reading the file

Yes — some controllers cap the number of nodes per file or per entity, and beyond that the file won't load or the head stutters. Cutting points with true arcs usually fixes it.

Summary

Almost all "too many points" DXFs come from curves exploded into short straight lines instead of true arcs. Fix it by using true circles and arcs (the C and fillet commands), setting a sensible tolerance of 0.05–0.1 mm, deleting duplicate lines, joining broken edges into single polylines, and removing text that doesn't need cutting. Measure key sizes with M before and after to confirm the shape is unchanged — the file shrinks and the cutter runs smoothly.